View PIC16C72A-04IP_1127135.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

PIC16C62B/72A
28-Pin 8-Bit CMOS Microcontrollers
Microcontroller Core Features:
* High-performance RISC CPU * Only 35 single word instructions to learn * All single cycle instructions except for program branches, which are two cycle * Operating speed: DC - 20 MHz clock input DC - 200 ns instruction cycle * 2K x 14 words of Program Memory, 128 x 8 bytes of Data Memory (RAM) * Interrupt capability * Eight level deep hardware stack * Direct, indirect, and relative addressing modes * Power-on Reset (POR) * Power-up Timer (PWRT) and Oscillator Start-up Timer (OST) * Watchdog Timer (WDT) with its own on-chip RC oscillator for reliable operation * Brown-out detection circuitry for Brown-out Reset (BOR) * Programmable code-protection * Power saving SLEEP mode * Selectable oscillator options * Low-power, high-speed CMOS EPROM technology * Fully static design * In-Circuit Serial ProgrammingTM (ICSP) * Wide operating voltage range: 2.5V to 5.5V * High Sink/Source Current 25/25 mA * Commercial, Industrial and Extended temperature ranges * Low-power consumption: - < 2 mA @ 5V, 4 MHz - 22.5 A typical @ 3V, 32 kHz - < 1 A typical standby current
Pin Diagram
SDIP, SOIC, SSOP, Windowed CERDIP
MCLR/VPP RA0/AN0 RA1/AN1 RA2/AN2 RA3/AN3/VREF RA4/T0CKI RA5/SS/AN4 VSS OSC1/CLKIN OSC2/CLKOUT RC0/T1OSO/T1CKI RC1/T1OSI RC2/CCP1 RC3/SCK/SCL *1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0/INT VDD VSS RC7 RC6 RC5/SDO RC4/SDI/SDA
Peripheral Features:
* Timer0: 8-bit timer/counter with 8-bit prescaler * Timer1: 16-bit timer/counter with prescaler, can be incremented during sleep via external crystal/clock * Timer2: 8-bit timer/counter with 8-bit period register, prescaler and postscaler * Capture, Compare, PWM module * Capture is 16-bit, max. resolution is 12.5 ns, Compare is 16-bit, max. resolution is 200 ns, PWM maximum resolution is 10-bit * 8-bit multi-channel Analog-to-Digital converter * Synchronous Serial Port (SSP) with Enhanced SPITM and I2CTM
(c) 1999 Microchip Technology Inc.
Preliminary
PIC16C72A
DS35008B-page 1
PIC16C62B/72A
Pin Diagrams
SDIP, SOIC, SSOP, Windowed CERDIP
MCLR/VPP RA0 RA1 RA2 RA3 RA4/T0CKI RA5/SS VSS OSC1/CLKIN OSC2/CLKOUT RC0/T1OSO/T1CKI RC1/T1OSI RC2/CCP1 RC3/SCK/SCL *1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 RB7 RB6 RB5 RB4 RB3 RB2 RB1 RB0/INT VDD VSS RC7 RC6 RC5/SDO RC4/SDI/SDA
Key Features PICmicroTM Mid-Range Reference Manual (DS33023) Operating Frequency Resets (and Delays) Program Memory (14-bit words) Data Memory (bytes) Interrupts I/O Ports Timers Capture/Compare/PWM modules Serial Communications 8-bit Analog-to-Digital Module
PIC16C62B
PIC16C62B DC - 20 MHz POR, BOR (PWRT, OST) 2K 128 7 Ports A,B,C 3 1 SSP --
PIC16C72A DC - 20 MHz POR, BOR (PWRT, OST) 2K 128 8 Ports A,B,C 3 1 SSP 5 input channels
DS35008B-page 2
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
Table of Contents
1.0 Device Overview .................................................................................................................................................... 5 2.0 Memory Organization ............................................................................................................................................. 7 3.0 I/O Ports ............................................................................................................................................................... 19 4.0 Timer0 Module ..................................................................................................................................................... 25 5.0 Timer1 Module ..................................................................................................................................................... 27 6.0 Timer2 Module ..................................................................................................................................................... 31 7.0 Capture/Compare/PWM (CCP) Module ............................................................................................................... 33 8.0 Synchronous Serial Port (SSP) Module ............................................................................................................... 39 9.0 Analog-to-Digital Converter (A/D) Module ............................................................................................................ 49 10.0 Special Features of the CPU................................................................................................................................ 55 11.0 Instruction Set Summary ...................................................................................................................................... 67 12.0 Development Support........................................................................................................................................... 75 13.0 Electrical Characteristics ...................................................................................................................................... 81 14.0 DC and AC Characteristics Graphs and Tables................................................................................................. 103 15.0 Packaging Information........................................................................................................................................ 105 Appendix A: Revision History ................................................................................................................................... 111 Appendix B: Conversion Considerations .................................................................................................................. 111 Appendix C: Migration from Base-line to Mid-Range Devices .................................................................................. 112 Index ........................................................................................................................................................................... 113 On-Line Support.......................................................................................................................................................... 117 Reader Response ....................................................................................................................................................... 118 PIC16C62B/72A Product Identification System .......................................................................................................... 119
To Our Valued Customers
Most Current Data Sheet
To obtain the most up-to-date version of this data sheet, please register at our Worldwide Web site at: http://www.microchip.com You can determine the version of a data sheet by examining its literature number found on the bottom outside corner of any page. The last character of the literature number is the version number. e.g., DS30000A is version A of document DS30000.
New Customer Notification System
Register on our web site (www.microchip.com/cn) to receive the most current information on our products.
Errata
An errata sheet may exist for current devices, describing minor operational differences (from the data sheet) and recommended workarounds. As device/documentation issues become known to us, we will publish an errata sheet. The errata will specify the revision of silicon and revision of document to which it applies. To determine if an errata sheet exists for a particular device, please check with one of the following: * Microchip's Worldwide Web site; http://www.microchip.com * Your local Microchip sales office (see last page) * The Microchip Corporate Literature Center; U.S. FAX: (480) 786-7277 When contacting a sales office or the literature center, please specify which device, revision of silicon and data sheet (include literature number) you are using.
Corrections to this Data Sheet
We constantly strive to improve the quality of all our products and documentation. We have spent a great deal of time to ensure that this document is correct. However, we realize that we may have missed a few things. If you find any information that is missing or appears in error, please: * Fill out and mail in the reader response form in the back of this data sheet. * E-mail us at webmaster@microchip.com. We appreciate your assistance in making this a better document.
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 3
PIC16C62B/72A
NOTES:
DS35008B-page 4
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
1.0 DEVICE OVERVIEW
This document contains device-specific information. Additional information may be found in the PICmicroTM Mid-Range Reference Manual, (DS33023), which may be obtained from your local Microchip Sales Representative or downloaded from the Microchip website. The Reference Manual should be considered a complementary document to this data sheet, and is highly recommended reading for a better understanding of the device architecture and operation of the peripheral modules. There are two devices (PIC16C62B, PIC16C72A) covered by this datasheet. The PIC16C62B does not have the A/D module implemented. Figure 1-1 is the block diagram for both devices. The pinouts are listed in Table 1-1.
FIGURE 1-1:
PIC16C62B/PIC16C72A BLOCK DIAGRAM
13 Program Counter EPROM 2K x 14 Program Memory 8 Level Stack (13-bit) RAM 128 x 8 File Registers RAM Addr(1) 9 PORTB Data Bus 8 PORTA RA0/AN0(2) RA1/AN1(2) RA2/AN2(2) RA3/AN3/VREF(2) RA4/T0CKI RA5/SS/AN4(2)
Program Bus
14 Instruction reg Direct Addr 7
Addr MUX 8 Indirect Addr RB0/INT RB7:RB1
FSR reg STATUS reg 8 3 Power-up Timer Instruction Decode & Control Timing Generation OSC1/CLKIN OSC2/CLKOUT Oscillator Start-up Timer Power-on Reset Watchdog Timer Brown-out Reset 8 W reg ALU PORTC
MUX
RC0/T1OSO/T1CKI RC1/T1OSI RC2/CCP1 RC3/SCK/SCL RC4/SDI/SDA RC5/SDO RC6 RC7
MCLR
VDD, VSS
Timer0
Timer1
Timer2
CCP1
Synchronous Serial Port
A/D(2)
Note 1: Higher order bits are from the STATUS register. 2: The A/D module is not available on the PIC16C62B.
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 5
PIC16C62B/72A
TABLE 1-1
Pin Name OSC1/CLKIN OSC2/CLKOUT
PIC16C62B/PIC16C72A PINOUT DESCRIPTION
DIP Pin# 9 10 SOIC Pin# 9 10 I/O/P Type I O Buffer Type Description
ST/CMOS(3) Oscillator crystal input/external clock source input. -- Oscillator crystal output. Connects to crystal or resonator in crystal oscillator mode. In RC mode, the OSC2 pin outputs CLKOUT which has 1/4 the frequency of OSC1, and denotes the instruction cycle rate. Master clear (reset) input or programming voltage input. This pin is an active low reset to the device. PORTA is a bi-directional I/O port. RA0 can also be analog input 0 RA1 can also be analog input 1 RA2 can also be analog input 2 RA3 can also be analog input 3 or analog reference voltage RA4 can also be the clock input to the Timer0 module. Output is open drain type. RA5 can also be analog input 4 or the slave select for the synchronous serial port. PORTB is a bi-directional I/O port. PORTB can be software programmed for internal weak pull-up on all inputs.
MCLR/VPP
1
1
I/P
ST
RA0/AN0(4) RA1/AN1(4) RA2/AN2
(4) (4)
2 3 4 5 6 7
2 3 4 5 6 7
I/O I/O I/O I/O I/O I/O
TTL TTL TTL TTL ST TTL
RA3/AN3/VREF RA4/T0CKI
RA5/SS/AN4(4)
RB0/INT RB1 RB2 RB3 RB4 RB5 RB6 RB7 RC0/T1OSO/T1CKI RC1/T1OSI RC2/CCP1 RC3/SCK/SCL RC4/SDI/SDA RC5/SDO RC6 RC7 VSS VDD Legend: I = input Note 1: 2: 3: 4:
21 22 23 24 25 26 27 28 11 12 13 14 15 16 17 18 8, 19 20
21 22 23 24 25 26 27 28 11 12 13 14 15 16 17 18 8, 19 20
I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O I/O P P
TTL/ST(1) TTL TTL TTL TTL TTL TTL/ST(2) TTL/ST(2) ST ST ST ST ST ST ST ST -- --
RB0 can also be the external interrupt pin.
Interrupt on change pin. Interrupt on change pin. Interrupt on change pin. Serial programming clock. Interrupt on change pin. Serial programming data. PORTC is a bi-directional I/O port. RC0 can also be the Timer1 oscillator output or Timer1 clock input. RC1 can also be the Timer1 oscillator input. RC2 can also be the Capture1 input/Compare1 output/ PWM1 output. RC3 can also be the synchronous serial clock input/output for both SPI and I2C modes. RC4 can also be the SPI Data In (SPI mode) or data I/O (I2C mode). RC5 can also be the SPI Data Out (SPI mode).
Ground reference for logic and I/O pins. Positive supply for logic and I/O pins.
O = output I/O = input/output P = power or program -- = Not used TTL = TTL input ST = Schmitt Trigger input This buffer is a Schmitt Trigger input when configured as the external interrupt. This buffer is a Schmitt Trigger input when used in serial programming mode. This buffer is a Schmitt Trigger input when configured in RC oscillator mode and a CMOS input otherwise. The A/D module is not available on the PIC16C62B.
DS35008B-page 6
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
2.0 MEMORY ORGANIZATION
FIGURE 2-1:
There are two memory blocks in each of these microcontrollers. Each block (Program Memory and Data Memory) has its own bus, so that concurrent access can occur. Additional information on device memory may be found in the PICmicroTM Mid-Range Reference Manual, (DS33023).
PROGRAM MEMORY MAP AND STACK
PC<12:0>
CALL, RETURN RETFIE, RETLW
13
Stack Level 1
2.1
Program Memory Organization
Stack Level 8 Reset Vector
The PIC16C62B/72A devices have a 13-bit program counter capable of addressing an 8K x 14 program memory space. Each device has 2K x 14 words of program memory. Accessing a location above 07FFh will cause a wraparound. User Memory Space The reset vector is at 0000h and the interrupt vector is at 0004h.
0000h
Interrupt Vector
0004h 0005h
On-chip Program Memory 07FFh 0800h
1FFFh
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 7
PIC16C62B/72A
2.2 Data Memory Organization FIGURE 2-2:
File Address 00h 01h 02h 03h 04h 05h 06h 07h 08h 09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh 10h 11h 12h 13h 14h 15h 16h 17h 18h 19h 1Ah 1Bh 1Ch 1Dh 1Eh 1Fh 20h General Purpose Registers 7Fh Bank 0 INDF(1) TMR0 PCL STATUS FSR PORTA PORTB PORTC
-- --
REGISTER FILE MAP
File Address INDF(1) PCL STATUS FSR TRISA TRISB TRISC
-- --
The data memory is partitioned into multiple banks which contain the General Purpose Registers and the Special Function Registers. Bits RP1 and RP0 are the bank select bits. RP1(1) = 00 = 01 = 10 = 11 RP0 (STATUS<6:5>)
80h 82h 83h 84h 85h 86h 87h 88h 89h 8Ah 8Bh 8Ch 8Dh 8Eh 8Fh 90h 91h 92h 93h 94h 95h 96h 97h 98h 99h 9Ah 9Bh 9Ch 9Dh 9Eh 9Fh A0h BFh C0h FFh
OPTION_REG 81h
Bank0 Bank1 Bank2 (not implemented) Bank3 (not implemented)
Note 1: Maintain this bit clear to ensure upward compatibility with future products.
Each bank extends up to 7Fh (128 bytes). The lower locations of each bank are reserved for the Special Function Registers. Above the Special Function Registers are General Purpose Registers, implemented as static RAM. All implemented banks contain Special Function Registers. Some "high use" Special Function Registers from one bank may be mirrored in another bank for code reduction and quicker access. 2.2.1 GENERAL PURPOSE REGISTER FILE
PCLATH INTCON PIR1
--
PCLATH INTCON PIE1
--
TMR1L TMR1H T1CON TMR2 T2CON SSPBUF SSPCON CCPR1L CCPR1H CCP1CON
-- -- -- -- -- --
PCON
-- -- --
The register file can be accessed either directly, or indirectly through the File Select Register FSR (Section 2.5).
PR2 SSPADD SSPSTAT
-- -- -- -- -- -- -- -- -- --
ADRES(2) ADCON0(2)
ADCON1(2) General Purpose Registers
-- -- --
Bank 1
Unimplemented data memory locations, read as '0'. Note 1: Not a physical register. 2: These registers are not implemented on the PIC16C62B, read as '0'.
DS35008B-page 8
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
2.2.2 SPECIAL FUNCTION REGISTERS The Special Function Registers are registers used by the CPU and Peripheral Modules for controlling the desired operation of the device. These registers are implemented as static RAM. A list of these registers is given in Table 2-1. The Special Function Registers can be classified into two sets; core (CPU) and peripheral. Those registers associated with the core functions are described in detail in this section. Those related to the operation of the peripheral features are described in detail in the peripheral feature section.
TABLE 2-1
Addr
SPECIAL FUNCTION REGISTER SUMMARY
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR Value on all other resets (4)
Bank 0 00h 01h 02h 03h 04h 05h 06h 07h 08h-09h 0Ah 0Bh 0Ch 0Dh 0Eh 0Fh 10h 11h 12h 13h 14h 15h 16h 17h 18h-1Dh 1Eh 1Fh INDF(1) TMR0 PCL(1) STATUS FSR(1) PORTA
(6,7) (1)
Addressing this location uses contents of FSR to address data memory (not a physical register) 0000 0000 0000 0000 Timer0 module's register Program Counter's (PC) Least Significant Byte IRP(5) RP1(5) RP0 TO PD Z DC C xxxx xxxx uuuu uuuu 0000 0000 0000 0000 0001 1xxx 000q quuu xxxx xxxx uuuu uuuu --0x 0000 --0u 0000 xxxx xxxx uuuu uuuu xxxx xxxx uuuu uuuu -- -- T0IE -- Write Buffer for the upper 5 bits of the Program Counter INTE -- RBIE SSPIF T0IF CCP1IF INTF TMR2IF RBIF TMR1IF --
Indirect data memory address pointer -- -- PORTA Data Latch when written: PORTA pins when read
PORTB(6,7) PORTC
(6,7)
PORTB Data Latch when written: PORTB pins when read PORTC Data Latch when written: PORTC pins when read Unimplemented -- GIE -- -- PEIE ADIF
(3)
-- PCLATH
(1,2)
---0 0000 ---0 0000 0000 000x 0000 000u -0-- 0000 -0-- 0000 -- --
INTCON(1) PIR1 -- TMR1L TMR1H T1CON TMR2 T2CON SSPBUF SSPCON CCPR1L CCPR1H CCP1CON -- ADRES(3) ADCON0(3)
Unimplemented Holding register for the Least Significant Byte of the 16-bit TMR1 register Holding register for the Most Significant Byte of the 16-bit TMR1 register -- -- T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON
xxxx xxxx uuuu uuuu xxxx xxxx uuuu uuuu --00 0000 --uu uuuu 0000 0000 0000 0000
Timer2 module's register -- TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON
T2CKPS1 T2CKPS0 -000 0000 -000 0000 xxxx xxxx uuuu uuuu
Synchronous Serial Port Receive Buffer/Transmit Register WCOL SSPOV SSPEN CKP SSPM3 SSPM2 SSPM1 SSPM0
0000 0000 0000 0000 xxxx xxxx uuuu uuuu xxxx xxxx uuuu uuuu
Capture/Compare/PWM Register1 (LSB) Capture/Compare/PWM Register1 (MSB) -- -- CCP1X CCP1Y CCP1M3 CCP1M2 CCP1M1 CCP1M0
--00 0000 --00 0000 -- --
Unimplemented A/D Result Register ADCS1 ADCS0 CHS2 CHS1 CHS0 GO/DONE -- ADON
xxxx xxxx uuuu uuuu 0000 00-0 0000 00-0
Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as '0', Shaded locations are unimplemented, read as '0'. Note 1: These registers can be addressed from either bank. 2: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for PC<12:8> whose contents are transferred to the upper byte of the program counter. 3: A/D not implemented on the PIC16C62B, maintain as '0'. 4: Other (non power-up) resets include: external reset through MCLR and the Watchdog Timer Reset. 5: The IRP and RP1 bits are reserved. Always maintain these bits clear. 6: On any device reset, these pins are configured as inputs. 7: This is the value that will be in the port output latch.
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 9
PIC16C62B/72A
TABLE 2-1
Addr
SPECIAL FUNCTION REGISTER SUMMARY (Cont.'d)
Name Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR Value on all other resets (4)
Bank 1 80h 81h 82h 83h 84h 85h 86h 87h 88h-89h 8Ah 8Bh 8Ch 8Dh 8Eh 8Fh-91h 92h 93h 94h 95h-9Eh 9Fh PR2 SSPADD SSPSTAT -- ADCON1
(3)
INDF(1) OPTION_REG PCL(1) STATUS FSR(1) TRISA TRISB TRISC -- PCLATH
(1,2) (1)
Addressing this location uses contents of FSR to address data memory (not a physical register) 0000 0000 0000 0000 RBPU INTEDG T0CS T0SE PSA PS2 PS1 PS0 1111 1111 1111 1111 0000 0000 0000 0000 PD Z DC C 0001 1xxx 000q quuu xxxx xxxx uuuu uuuu --11 1111 --11 1111 1111 1111 1111 1111 1111 1111 1111 1111 -- -- T0IE -- Write Buffer for the upper 5 bits of the Program Counter INTE -- RBIE SSPIE T0IF CCP1IE INTF TMR2IE RBIF TMR1IE --
Program Counter's (PC) Least Significant Byte IRP
(5)
RP1
(5)
RP0
TO
Indirect data memory address pointer -- -- PORTA Data Direction Register
PORTB Data Direction Register PORTC Data Direction Register Unimplemented -- GIE -- -- PEIE ADIE
(3)
---0 0000 ---0 0000 0000 000x 0000 000u -0-- 0000 -0-- 0000 -- --
INTCON(1) PIE1 -- PCON --
Unimplemented -- -- -- -- -- -- POR BOR
---- --qq ---- --uu -- --
Unimplemented Timer2 Period Register Synchronous Serial Port (I2C mode) Address Register SMP CKE D/A P S R/W UA BF
1111 1111 1111 1111 0000 0000 0000 0000 0000 0000 0000 0000 -- -- -- -- PCFG2 PCFG1 PCFG0 ---- -000 -- ---- -000
Unimplemented -- --
Legend: x = unknown, u = unchanged, q = value depends on condition, - = unimplemented, read as '0', Shaded locations are unimplemented, read as '0'. Note 1: These registers can be addressed from either bank. 2: The upper byte of the program counter is not directly accessible. PCLATH is a holding register for PC<12:8> whose contents are transferred to the upper byte of the program counter. 3: A/D not implemented on the PIC16C62B, maintain as '0'. 4: Other (non power-up) resets include: external reset through MCLR and the Watchdog Timer Reset. 5: The IRP and RP1 bits are reserved. Always maintain these bits clear. 6: On any device reset, these pins are configured as inputs. 7: This is the value that will be in the port output latch.
DS35008B-page 10
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
2.2.2.1 STATUS REGISTER The STATUS register, shown in Register 2-1, contains the arithmetic status of the ALU, the RESET status and the bank select bits for data memory. The STATUS register can be the destination for any instruction, as with any other register. If the STATUS register is the destination for an instruction that affects the Z, DC or C bits, the write to these three bits is disabled. These bits are set or cleared according to the device logic. The TO and PD bits are not writable. The result of an instruction with the STATUS register as destination may be different than intended. For example, CLRF STATUS will clear the upper-three bits and set the Z bit. This leaves the STATUS register as 000u u1uu (where u = unchanged). It is recommended, therefore, that only BCF, BSF, SWAPF and MOVWF instructions are used to alter the STATUS register, because these instructions do not affect the Z, C or DC bits from the STATUS register. For other instructions, not affecting any status bits, see the "Instruction Set Summary." Note 1: The IRP and RP1 bits are reserved. Maintain these bits clear to ensure upward compatibility with future products. Note 2: The C and DC bits operate as a borrow and digit borrow bit, respectively, in subtraction. See the SUBLW and SUBWF instructions.
REGISTER 2-1:
R/W-0 IRP bit7 R/W-0 RP1
STATUS REGISTER (ADDRESS 03h, 83h)
R/W-0 RP0 R-1 TO R-1 PD R/W-x Z R/W-x DC R/W-x C bit0
R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset
bit 7:
IRP: Register Bank Select bit (used for indirect addressing) (reserved, maintain clear)
bit 6-5: RP1:RP0: Register Bank Select bits (used for direct addressing) 01 = Bank 1 (80h - FFh) 00 = Bank 0 (00h - 7Fh) Each bank is 128 bytes Note: RP1 is reserved, maintain clear bit 4: TO: Time-out bit 1 = After power-up, CLRWDT instruction, or SLEEP instruction 0 = A WDT time-out occurred PD: Power-down bit 1 = After power-up or by the CLRWDT instruction 0 = By execution of the SLEEP instruction Z: Zero bit 1 = The result of an arithmetic or logic operation is zero 0 = The result of an arithmetic or logic operation is not zero DC: Digit carry/borrow bit (ADDWF, ADDLW,SUBLW,SUBWF instructions) (for borrow, the polarity is reversed) 1 = A carry-out from the 4th low order bit of the result occurred 0 = No carry-out from the 4th low order bit of the result C: Carry/borrow bit (ADDWF, ADDLW,SUBLW,SUBWF instructions) (for borrow, the polarity is reversed) 1 = A carry-out from the most significant bit of the result occurred 0 = No carry-out from the most significant bit of the result occurred Note: For borrow, the polarity is reversed. A subtraction is executed by adding the two's complement of the second operand. For rotate (RRF, RLF) instructions, this bit is loaded with either the high or low order bit of the source register.
bit 3:
bit 2:
bit 1:
bit 0:
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 11
PIC16C62B/72A
2.2.2.2 OPTION_REG REGISTER Note: To achieve a 1:1 prescaler assignment for the TMR0 register, assign the prescaler to the Watchdog Timer. The OPTION_REG register is a readable and writable register, which contains various control bits to configure the TMR0 prescaler/WDT postscaler (single assignable register known as the prescaler), the External INT Interrupt, TMR0 and the weak pull-ups on PORTB.
REGISTER 2-2:
R/W-1 RBPU bit7 R/W-1 INTEDG
OPTION_REG REGISTER (ADDRESS 81h)
R/W-1 T0CS R/W-1 T0SE R/W-1 PSA R/W-1 PS2 R/W-1 PS1 R/W-1 PS0 bit0 R = Readable bit W = Writable bit - n = Value at POR reset
bit 7:
RBPU: PORTB Pull-up Enable bit 1 = PORTB pull-ups are disabled 0 = PORTB pull-ups are enabled for all PORTB inputs INTEDG: Interrupt Edge Select bit 1 = Interrupt on rising edge of RB0/INT pin 0 = Interrupt on falling edge of RB0/INT pin T0CS: TMR0 Clock Source Select bit 1 = Transition on RA4/T0CKI pin 0 = Internal instruction cycle clock (CLKOUT) T0SE: TMR0 Source Edge Select bit 1 = Increment on high-to-low transition on RA4/T0CKI pin 0 = Increment on low-to-high transition on RA4/T0CKI pin PSA: Prescaler Assignment bit 1 = Prescaler is assigned to the WDT 0 = Prescaler is assigned to the Timer0 module
bit 6:
bit 5:
bit 4:
bit 3:
bit 2-0: PS2:PS0: Prescaler Rate Select bits
Bit Value 000 001 010 011 100 101 110 111 TMR0 Rate 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128 1 : 256 WDT Rate 1:1 1:2 1:4 1:8 1 : 16 1 : 32 1 : 64 1 : 128
DS35008B-page 12
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
2.2.2.3 INTCON REGISTER Note: Interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the global enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt. The INTCON Register is a readable and writable register, which contains various interrupt enable and flag bits for the TMR0 register overflow, RB Port change and External RB0/INT pin interrupts.
REGISTER 2-3:
R/W-0 GIE bit7 R/W-0 PEIE
INTCON REGISTER (ADDRESS 0Bh, 8Bh)
R/W-0 T0IE R/W-0 INTE R/W-0 RBIE R/W-0 T0IF R/W-0 INTF R/W-x RBIF bit0 R = Readable bit W = Writable bit - n = Value at POR reset
bit 7:
GIE: Global Interrupt Enable bit 1 = Enables all un-masked interrupts 0 = Disables all interrupts PEIE: Peripheral Interrupt Enable bit 1 = Enables all un-masked peripheral interrupts 0 = Disables all peripheral interrupts T0IE: TMR0 Overflow Interrupt Enable bit 1 = Enables the TMR0 interrupt 0 = Disables the TMR0 interrupt IINTE: RB0/INT External Interrupt Enable bit 1 = Enables the RB0/INT external interrupt 0 = Disables the RB0/INT external interrupt RBIE: RB Port Change Interrupt Enable bit 1 = Enables the RB port change interrupt 0 = Disables the RB port change interrupt T0IF: TMR0 Overflow Interrupt Flag bit 1 = TMR0 register has overflowed (software must clear bit) 0 = TMR0 register did not overflow INTF: RB0/INT External Interrupt Flag bit 1 = The RB0/INT external interrupt occurred (software must clear bit) 0 = The RB0/INT external interrupt did not occur RBIF: RB Port Change Interrupt Flag bit 1 = At least one of the RB7:RB4 input pins have changed state (clear by reading PORTB) 0 = None of the RB7:RB4 input pins have changed state
bit 6:
bit 5:
bit 4:
bit 3:
bit 2:
bit 1:
bit 0:
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 13
PIC16C62B/72A
2.2.2.4 PIE1 REGISTER Note: This register contains the individual enable bits for the peripheral interrupts. Bit PEIE (INTCON<6>) must be set to enable any peripheral interrupt.
REGISTER 2-4:
U-0
--
PIE1 REGISTER (ADDRESS 8Ch)
U-0
--
R/W-0 ADIE(1)
U-0
--
R/W-0 SSPIE
R/W-0 CCP1IE
R/W-0 TMR2IE
R/W-0 TMR1IE bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset
bit7
bit 7: bit 6:
Unimplemented: Read as `0' ADIE(1): A/D Converter Interrupt Enable bit 1 = Enables the A/D interrupt 0 = Disables the A/D interrupt SSPIE: Synchronous Serial Port Interrupt Enable bit 1 = Enables the SSP interrupt 0 = Disables the SSP interrupt CCP1IE: CCP1 Interrupt Enable bit 1 = Enables the CCP1 interrupt 0 = Disables the CCP1 interrupt TMR2IE: TMR2 to PR2 Match Interrupt Enable bit 1 = Enables the TMR2 to PR2 match interrupt 0 = Disables the TMR2 to PR2 match interrupt TMR1IE: TMR1 Overflow Interrupt Enable bit 1 = Enables the TMR1 overflow interrupt 0 = Disables the TMR1 overflow interrupt
bit 5-4: Unimplemented: Read as `0' bit 3:
bit 2:
bit 1:
bit 0:
Note 1: The PIC16C62B does not have an A/D module. This bit location is reserved on these devices. Always maintain this bit clear.
DS35008B-page 14
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
2.2.2.5 PIR1 REGISTER Note: This register contains the individual flag bits for the Peripheral interrupts. Interrupt flag bits are set when an interrupt condition occurs, regardless of the state of its corresponding enable bit or the global enable bit, GIE (INTCON<7>). User software should ensure the appropriate interrupt flag bits are clear prior to enabling an interrupt.
REGISTER 2-5:
U-0
--
PIR1 REGISTER (ADDRESS 0Ch)
U-0
--
R/W-0 ADIF(1)
U-0
--
R/W-0 SSPIF
R/W-0 CCP1IF
R/W-0 TMR2IF
R/W-0 TMR1IF bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset
bit7
bit 7: bit 6:
Unimplemented: Read as `0' ADIF(1): A/D Converter Interrupt Flag bit 1 = An A/D conversion completed (must be cleared in software) 0 = The A/D conversion is not complete SSPIF: Synchronous Serial Port Interrupt Flag bit 1 = The transmission/reception is complete (must be cleared in software) 0 = Waiting to transmit/receive CCP1IF: CCP1 Interrupt Flag bit Capture Mode 1 = A TMR1 register capture occurred (must be cleared in software) 0 = No TMR1 register capture occurred Compare Mode 1 = A TMR1 register compare match occurred (must be cleared in software) 0 = No TMR1 register compare match occurred PWM Mode Unused in this mode TMR2IF: TMR2 to PR2 Match Interrupt Flag bit 1 = TMR2 to PR2 match occurred (must be cleared in software) 0 = No TMR2 to PR2 match occurred TMR1IF: TMR1 Overflow Interrupt Flag bit 1 = TMR1 register overflowed (must be cleared in software) 0 = TMR1 register did not overflow
bit 5-4: Unimplemented: Read as `0' bit 3:
bit 2:
bit 1:
bit 0:
Note 1: The PIC16C62B does not have an A/D module. This bit location is reserved on these devices. Always maintain this bit clear.
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 15
PIC16C62B/72A
2.2.2.6 PCON REGISTER Note: The Power Control register (PCON) contains flag bits to allow differentiation between a Power-on Reset (POR), Brown-Out Reset (BOR) and resets from other sources. . On Power-on Reset, the state of the BOR bit is unknown and is not predictable. If the BODEN bit in the configuration word is set, the user must first set the BOR bit on a POR, and check it on subsequent resets. If BOR is cleared while POR remains set, a Brown-out reset has occurred. If the BODEN bit is clear, the BOR bit may be ignored.
REGISTER 2-6:
U-0 -- bit7 U-0 --
PCON REGISTER (ADDRESS 8Eh)
U-0 -- U-0 -- U-0 -- U-0 -- R/W-0 POR R/W-q BOR bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset
bit 7-2: Unimplemented: Read as '0' bit 1: POR: Power-on Reset Status bit 1 = No Power-on Reset occurred 0 = A Power-on Reset occurred (must be set in software after a Power-on Reset occurs) BOR: Brown-out Reset Status bit 1 = No Brown-out Reset occurred 0 = A Brown-out Reset occurred (must be set in software after a Brown-out Reset occurs)
bit 0:
DS35008B-page 16
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
2.3 PCL and PCLATH 2.4 Program Memory Paging
The program counter (PC) specifies the address of the instruction to fetch for execution. The PC is 13 bits wide. The low byte is called the PCL register and is readable and writable. The high byte is called the PCH register. This register contains the PC<12:8> bits and is not directly accessible. All updates to the PCH register go through the PCLATH register. 2.3.1 STACK The CALL and GOTO instructions provide 11 bits of address to allow branching within any 2K program memory page. When doing a CALL or GOTO instruction, the upper bit of the address is provided by PCLATH<3>. The user must ensure that the page select bit is programmed to address the proper program memory page. If a return from a CALL instruction (or interrupt) is executed, the entire 13-bit PC is popped from the stack. Therefore, manipulation of the PCLATH<3> bit is not required for the return instructions.
The stack allows any combination of up to 8 program calls and interrupts to occur. The stack contains the return address from this branch in program execution. Mid-range devices have an 8 level deep hardware stack. The stack space is not part of either program or data space and the stack pointer is not accessible. The PC is PUSHed onto the stack when a CALL instruction is executed or an interrupt causes a branch. The stack is POPed in the event of a RETURN, RETLW or a RETFIE instruction execution. PCLATH is not modified when the stack is PUSHed or POPed. After the stack has been PUSHed eight times, the ninth push overwrites the value that was stored from the first push. The tenth push overwrites the second push (and so on).
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 17
PIC16C62B/72A
2.5 Indirect Addressing, INDF and FSR Registers EXAMPLE 2-1: HOW TO CLEAR RAM USING INDIRECT ADDRESSING
0x20 FSR INDF FSR FSR,4 NEXT ;initialize pointer ; to RAM ;clear INDF register ;inc pointer ;all done? ;NO, clear next ;YES, continue
The INDF register is not a physical register. Addressing INDF actually addresses the register whose address is contained in the FSR register (FSR is a pointer). Reading INDF itself indirectly (FSR = 0) will produce 00h. Writing to the INDF register indirectly results in a no-operation (although STATUS bits may be affected). A simple program to clear RAM locations 20h-2Fh using indirect addressing is shown in Example 2-1.
NEXT
movlw movwf clrf incf btfss goto :
CONTINUE
An effective 9-bit address is obtained by concatenating the 8-bit FSR register and the IRP bit (STATUS<7>), as shown in Figure 2-3. However, IRP is not used in the PIC16C62B/72A.
FIGURE 2-3:
DIRECT/INDIRECT ADDRESSING
Direct Addressing Indirect Addressing
0 IRP 7 FSR register 0
RP1:RP0
6
from opcode
(1)
bank select location select 00 00h 01 80h 10 100h 11 180h
(1)
bank select location select
Data Memory
not used (2) (2)
7Fh
FFh
17Fh
1FFh
Bank 0
Bank 1
Bank 2
Bank 3
Note 1: Maintain clear for upward compatibility with future products. 2: Not implemented.
DS35008B-page 18
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
3.0 I/O PORTS
FIGURE 3-1:
Data Bus WR Port
Some I/O port pins are multiplexed with an alternate function for the peripheral features on the device. In general, when a peripheral is enabled, that pin may not be used as a general purpose I/O pin. Additional information on I/O ports may be found in the PICmicroTM Mid-Range Reference Manual, (DS33023).
BLOCK DIAGRAM OF RA3:RA0 AND RA5 PINS
Q VDD
D
CK
Q
P
Data Latch
3.1
PORTA and the TRISA Register
WR TRIS
D
Q
N
I/O pin(1)
PORTA is a 6-bit wide bi-directional port. The corresponding data direction register is TRISA. Setting a TRISA bit (=1) will make the corresponding PORTA pin an input, i.e., put the corresponding output driver in a hi-impedance mode. Clearing a TRISA bit (=0) will make the corresponding PORTA pin an output, (i.e., put the contents of the output latch on the selected pin). The PORTA register reads the state of the pins, whereas writing to it will write to the port latch. All write operations are read-modify-write operations. Therefore, a write to a port implies that the port pins are read, this value is modified, and then written to the port data latch. Pin RA4 is multiplexed with the Timer0 module clock input to become the RA4/T0CKI pin. The RA4/T0CKI pin is a Schmitt Trigger input and an open drain output. All other RA port pins have TTL input levels and full CMOS output drivers. Pin RA5 is multiplexed with the SSP to become the RA5/SS pin. On the PIC16C72A device, other PORTA pins are multiplexed with analog inputs and analog VREF input. The operation of each pin is selected by clearing/setting the control bits in the ADCON1 register (A/D Control Register1). Note: On a Power-on Reset, pins with analog functions are configured as analog inputs with digital input buffers disabled . A digital read of these pins will return '0'.
CK
Q
VSS Analog input mode (72A only) TTL input buffer D
TRIS Latch
RD TRIS Q
EN RD PORT
To A/D Converter (72A only) Note 1: I/O pins have protection diodes to VDD and VSS.
FIGURE 3-2:
Data Bus WR PORT
BLOCK DIAGRAM OF RA4/T0CKI PIN
D Q Q
CK
N Data Latch
D Q Q
I/O pin(1)
VSS Schmitt Trigger input buffer
The TRISA register controls the direction of the RA pins, even when they are being used as analog inputs. The user must ensure the bits in the TRISA register are maintained set when using them as analog inputs.
WR TRIS
CK
TRIS Latch
RD TRIS
Q D EN EN
RD PORT TMR0 clock input Note 1: I/O pin has protection diodes to VSS only.
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 19
PIC16C62B/72A
TABLE 3-1
Name RA0/AN0 RA1/AN1 RA2/AN2 RA3/AN3/VREF RA4/T0CKI
PORTA FUNCTIONS
Bit# bit0 bit1 bit2 bit3 bit4 Buffer TTL TTL TTL TTL ST Function Input/output or analog input(1) Input/output or analog input(1) Input/output or analog input(1) Input/output or analog input(1) or VREF(1) Input/output or external clock input for Timer0 Output is open drain type
RA5/SS/AN4 bit5 TTL Input/output or slave select input for synchronous serial port or analog input(1) Legend: TTL = TTL input, ST = Schmitt Trigger input
Note 1: The PIC16C62B does not implement the A/D module.
TABLE 3-2
Address Name 05h 05h 85h 9Fh PORTA
SUMMARY OF REGISTERS ASSOCIATED WITH PORTA
Bit 7 -- -- -- -- Bit 6 -- -- -- -- Bit 5 RA5 RA5 Bit 4 RA4 RA4 Bit 3 RA3 RA3 Bit 2 RA2 RA2 Bit 1 RA1 RA1 Bit 0 RA0 RA0 Value on POR, BOR --0x 0000 --xx xxxx --11 1111 PCFG1 PCFG0 ---- -000 Value on all other resets --0u 0000 --uu uuuu --11 1111 ---- -000
(for PIC16C72A only)
PORTA
(for PIC16C62B only)
TRISA ADCON1(1)
PORTA Data Direction Register -- -- -- PCFG2
Legend: x = unknown, u = unchanged, - = unimplemented locations read as '0'. Shaded cells are not used by PORTA.
Note 1: The PIC16C62B does not implement the A/D module. Maintain this register clear.
DS35008B-page 20
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
3.2 PORTB and the TRISB Register
PORTB is an 8-bit wide bi-directional port. The corresponding data direction register is TRISB. Setting a TRISB bit (=1) will make the corresponding PORTB pin an input, (i.e., put the corresponding output driver in a hi-impedance mode). Clearing a TRISB bit (=0) will make the corresponding PORTB pin an output, (i.e., put the contents of the output latch on the selected pin). Each of the PORTB pins has a weak internal pull-up. A single control bit can turn on all the pull-ups. This is performed by clearing bit RBPU (OPTION_REG<7>). The weak pull-up is automatically turned off when the port pin is configured as an output. The pull-ups are disabled on a Power-on Reset. Four of PORTB's pins, RB7:RB4, have an interrupt on change feature. Only pins configured as inputs can cause this interrupt to occur (i.e. any RB7:RB4 pin configured as an output is excluded from the interrupt on change comparison). The input pins (of RB7:RB4) are compared with the old value latched on the last read of PORTB. The "mismatch" outputs of RB7:RB4 are OR'ed together to generate the RB Port Change Interrupt with flag bit RBIF (INTCON<0>). This interrupt can wake the device from SLEEP. The user, in the interrupt service routine, can clear the interrupt in the following manner: a) b) Any read or write of PORTB. This will end the mismatch condition. Clear flag bit RBIF.
FIGURE 3-3:
RBPU(2)
BLOCK DIAGRAM OF RB3:RB0 PINS
VDD weak P pull-up Data Latch D Q CK TRIS Latch D Q I/O pin(1)
A mismatch condition will continue to set flag bit RBIF. Reading PORTB will end the mismatch condition and allow flag bit RBIF to be cleared. The interrupt on change feature is recommended for wake-up on key depression operation and operations where PORTB is only used for the interrupt on change feature. Polling of PORTB is not recommended while using the interrupt on change feature. RB0/INT is an external interupt pin and is configured using the INTEDG bit (OPTION_REG<6>). RB0/INT is discussed in detail in Section 10.10.1.
Data Bus WR Port
WR TRIS
CK
TTL Input Buffer
FIGURE 3-4:
RD TRIS Q RD Port D EN RBPU(2)
BLOCK DIAGRAM OF RB7:RB4 PINS
VDD weak P pull-up Data Latch D Q CK TRIS Latch D Q I/O pin(1)
Data Bus WR Port
RB0/INT Schmitt Trigger Buffer RD Port
Note 1: I/O pins have diode protection to VDD and VSS. 2: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (OPTION_REG<7>).
WR TRIS
CK
TTL Input Buffer
ST Buffer
RD TRIS Q RD Port Set RBIF
Latch D EN Q1
From other RB7:RB4 pins
Q
D RD Port EN Q3
RB7:RB6 in serial programming mode Note 1: I/O pins have diode protection to VDD and VSS. 2: To enable weak pull-ups, set the appropriate TRIS bit(s) and clear the RBPU bit (OPTION_REG<7>).
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 21
PIC16C62B/72A
TABLE 3-3
Name RB0/INT
PORTB FUNCTIONS
Bit# bit0 Buffer TTL/ST(1) Function
Input/output pin or external interrupt input. Internal software programmable weak pull-up. RB1 bit1 TTL Input/output pin. Internal software programmable weak pull-up. RB2 bit2 TTL Input/output pin. Internal software programmable weak pull-up. RB3 bit3 TTL Input/output pin. Internal software programmable weak pull-up. RB4 bit4 TTL Input/output pin (with interrupt on change). Internal software programmable weak pull-up. RB5 bit5 TTL Input/output pin (with interrupt on change). Internal software programmable weak pull-up. Input/output pin (with interrupt on change). RB6 bit6 TTL/ST(2) Internal software programmable weak pull-up. Serial programming clock. Input/output pin (with interrupt on change). RB7 bit7 TTL/ST(2) Internal software programmable weak pull-up. Serial programming data. Legend: TTL = TTL input, ST = Schmitt Trigger input
Note 1: This buffer is a Schmitt Trigger input when configured as the external interrupt. 2: This buffer is a Schmitt Trigger input when used in serial programming mode.
TABLE 3-4
Address 06h 86h 81h Name
SUMMARY OF REGISTERS ASSOCIATED WITH PORTB
Bit 7 RB7 Bit 6 RB6 Bit 5 RB5 Bit 4 RB4 Bit 3 RB3 Bit 2 RB2 Bit 1 RB1 Bit 0 RB0 Value on: POR, BOR xxxx xxxx 1111 1111 PSA PS2 PS1 PS0 1111 1111 Value on all other resets uuuu uuuu 1111 1111 1111 1111
PORTB TRISB OPTION_REG
PORTB Data Direction Register RBPU INTEDG T0CS T0SE
Legend: x = unknown, u = unchanged. Shaded cells are not used by PORTB.
DS35008B-page 22
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
3.3 PORTC and the TRISC Register
PORTC is an 8-bit wide bi-directional port. The corresponding data direction register is TRISC. Setting a TRISC bit (=1) will make the corresponding PORTC pin an input, (i.e., put the corresponding output driver in a hi-impedance mode). Clearing a TRISC bit (=0) will make the corresponding PORTC pin an output, (i.e., put the contents of the output latch on the selected pin). PORTC is multiplexed with several peripheral functions (Table 3-5). PORTC pins have Schmitt Trigger input buffers. When enabling peripheral functions, care should be taken in defining TRIS bits for each PORTC pin. Some peripherals override the TRIS bit to make a pin an output, while other peripherals override the TRIS bit to make a pin an input. Since the TRIS bit override maybe in effect while the peripheral is enabled, read-modifywrite instructions (BSF, BCF, XORWF) with TRISC as destination should be avoided. The user should refer to the corresponding peripheral section for the correct TRIS bit settings.
FIGURE 3-5:
PORTC BLOCK DIAGRAM (PERIPHERAL OUTPUT OVERRIDE)
PORT/PERIPHERAL Select(2) Peripheral Data Out Data Bus WR PORT
D CK Q
0 1
Q
VDD P
Data Latch WR TRIS
D CK Q Q
I/O pin(1) N VSS
TRIS Latch Schmitt Trigger
Q D EN
RD TRIS Peripheral OE(3) RD PORT Peripheral input
Note 1: I/O pins have diode protection to VDD and VSS. 2: Port/Peripheral select signal selects between port data and peripheral output. 3: Peripheral OE (output enable) is only activated if peripheral select is active.
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 23
PIC16C62B/72A
TABLE 3-5
Name RC0/T1OSO/T1CKI RC1/T1OSI RC2/CCP1 RC3/SCK/SCL RC4/SDI/SDA RC5/SDO RC6 RC7
PORTC FUNCTIONS
Bit# bit0 bit1 bit2 bit3 bit4 bit5 bit6 bit7 Buffer Function Type ST ST ST ST ST ST ST ST Input/output port pin or Timer1 oscillator output/Timer1 clock input Input/output port pin or Timer1 oscillator input Input/output port pin or Capture1 input/Compare1 output/PWM1 output RC3 can also be the synchronous serial clock for both SPI and I2C modes. RC4 can also be the SPI Data In (SPI mode) or data I/O (I2C mode). Input/output port pin or Synchronous Serial Port data output Input/output port pin Input/output port pin TRISC Override Yes Yes No No No No No No
Legend: ST = Schmitt Trigger input
TABLE 3-6
Address Name 07h 87h PORTC TRISC
SUMMARY OF REGISTERS ASSOCIATED WITH PORTC
Bit 7 RC7 Bit 6 RC6 Bit 5 RC5 Bit 4 RC4 Bit 3 RC3 Bit 2 RC2 Bit 1 RC1 Bit 0 RC0 Value on: POR, BOR xxxx xxxx 1111 1111 Value on all other resets uuuu uuuu 1111 1111
PORTC Data Direction Register
Legend: x = unknown, u = unchanged.
DS35008B-page 24
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
4.0 TIMER0 MODULE
The Timer0 module timer/counter has the following features: * 8-bit timer/counter - Read and write - INT on overflow * 8-bit software programmable prescaler * INT or EXT clock select - EXT clock edge select Figure 4-1 is a simplified block diagram of the Timer0 module. Additional information on timer modules is available in the PICmicroTM Mid-Range Reference Manual, (DS33023). Additional information on external clock requirements is available in the Electrical Specifications section of this manual, and in the PICmicroTM Mid-Range Reference Manual, (DS33023).
4.2
Prescaler
An 8-bit counter is available as a prescaler for the Timer0 module, or as a postscaler for the Watchdog Timer, respectively (Figure 4-2). For simplicity, this counter is being referred to as "prescaler" throughout this data sheet. There is only one prescaler available which is shared between the Timer0 module and the Watchdog Timer. A prescaler assignment for the Timer0 module means that there is no prescaler for the Watchdog Timer, and vice-versa. The prescaler is not readable or writable. The PSA and PS2:PS0 bits (OPTION_REG<3:0>) determine the prescaler assignment and prescale ratio. Clearing bit PSA will assign the prescaler to the Timer0 module. When the prescaler is assigned to the Timer0 module, prescale values of 1:2, 1:4, ..., 1:256 are selectable. Setting bit PSA will assign the prescaler to the Watchdog Timer (WDT). When the prescaler is assigned to the WDT, prescale values of 1:1, 1:2, ..., 1:128 are selectable. When assigned to the Timer0 module, all instructions writing to the TMR0 register (e.g. CLRF 1, MOVWF 1, BSF 1,x....etc.) will clear the prescaler. When assigned to WDT, a CLRWDT instruction will clear the prescaler along with the WDT. Note: Writing to TMR0 when the prescaler is assigned to Timer0 will clear the prescaler count, but will not change the prescaler assignment or ratio.
4.1
Timer0 Operation
Timer0 can operate as a timer or as a counter. Timer mode is selected by clearing bit T0CS (OPTION_REG<5>). In timer mode, the Timer0 module will increment every instruction cycle (without prescaler). If the TMR0 register is written, the increment is inhibited for the following two instruction cycles. The user can work around this by writing an adjusted value to the TMR0 register. Counter mode is selected by setting bit T0CS (OPTION_REG<5>). In counter mode, Timer0 will increment either on every rising or falling edge of pin RA4/T0CKI. The incrementing edge is determined by the Timer0 Source Edge Select bit T0SE (OPTION_REG<4>). Clearing bit T0SE selects the rising edge. Restrictions on the external clock input are discussed below. When an external clock input is used for Timer0, it must meet certain requirements. The requirements ensure the external clock can be synchronized with the internal phase clock (TOSC). Also, there is a delay in the actual incrementing of Timer0 after synchronization.
FIGURE 4-1:
TIMER0 BLOCK DIAGRAM
Data Bus FOSC/4 0 1 1 Programmable Prescaler T0SE 3 PS2, PS1, PS0 T0CS PSA Set interrupt flag bit T0IF on overflow PSout Sync with Internal clocks (TCY delay) TMR0 PSout 8
RA4/T0CKI pin
0
Note 1: T0CS, T0SE, PSA, PS2:PS0 (OPTION_REG<5:0>). 2: The prescaler is shared with Watchdog Timer (refer to Figure 4-2 for detailed block diagram).
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 25
PIC16C62B/72A
4.2.1 SWITCHING PRESCALER ASSIGNMENT
4.3
Timer0 Interrupt
The prescaler assignment is fully under software control, (i.e., it can be changed "on-the-fly" during program execution). Note: To avoid an unintended device RESET, a specific instruction sequence (shown in the PICmicroTM Mid-Range Reference Manual, DS33023) must be executed when changing the prescaler assignment from Timer0 to the WDT. This sequence must be followed even if the WDT is disabled.
The TMR0 interrupt is generated when the TMR0 register overflows from FFh to 00h. This overflow sets bit T0IF (INTCON<2>). The interrupt can be masked by clearing bit T0IE (INTCON<5>). Bit T0IF must be cleared in software by the Timer0 module interrupt service routine before re-enabling this interrupt. The TMR0 interrupt cannot awaken the processor from SLEEP since the timer is shut off during SLEEP.
FIGURE 4-2:
BLOCK DIAGRAM OF THE TIMER0/WDT PRESCALER
Data Bus 8 1 0 M U X SYNC 2 TCY TMR0 reg
CLKOUT (= Fosc/4)
0 RA4/T0CKI pin 1 T0SE
M U X
T0CS
PSA Prescaler
Set flag bit T0IF on Overflow
0 M U X
8-bit Prescaler 8 8 - to - 1MUX PS2:PS0
Watchdog Timer
1
PSA 0 MUX 1 PSA
WDT Enable bit
WDT Time-out Note: T0CS, T0SE, PSA, PS2:PS0 are (OPTION_REG<5:0>).
TABLE 4-1
Address 01h 0Bh,8Bh 81h 85h
REGISTERS ASSOCIATED WITH TIMER0
Name TMR0 INTCON OPTION_REG TRISA Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on: POR, BOR xxxx xxxx INTE T0SE RBIE PSA T0IF PS2 INTF PS1 RBIF PS0 0000 000x 1111 1111 --11 1111 Value on all other resets uuuu uuuu 0000 000u 1111 1111 --11 1111
Timer0 module's register GIE PEIE T0IE T0CS
RBPU INTEDG -- --
PORTA Data Direction Register
Legend: x = unknown, u = unchanged, - = unimplemented locations read as '0'. Shaded cells are not used by Timer0.
DS35008B-page 26
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
5.0 TIMER1 MODULE
5.1 Timer1 Operation
The Timer1 module timer/counter has the following features: * * * * * 16-bit timer/counter Readable and writable Internal or external clock select Interrupt on overflow from FFFFh to 0000h Reset from CCP module trigger Timer1 can operate in one of these modes: * As a timer * As a synchronous counter * As an asynchronous counter The operating mode is determined by the clock select bit, TMR1CS (T1CON<1>). In timer mode, Timer1 increments every instruction cycle. In counter mode, it increments on every rising edge of the external clock input. When the Timer1 oscillator is enabled (T1OSCEN is set), the RC1/T1OSI and RC0/T1OSO/T1CKI pins become inputs. That is, the TRISC<1:0> value is ignored. Timer1 also has an internal "reset input". This reset can be generated by the CCP module as a special event trigger (Section 7.0).
Timer1 has a control register, shown in Register 5-1. Timer1 can be enabled/disabled by setting/clearing control bit TMR1ON (T1CON<0>). Figure 5-1 is a simplified block diagram of the Timer1 module. Additional information on timer modules is available in the PICmicroTM Mid-Range Reference Manual, (DS33023).
REGISTER 5-1:T1CON: TIMER1 CONTROL REGISTER (ADDRESS 10h)
U-0 -- bit7 U-0 -- R/W-0 R/W-0 R/W-0 R/W-0 T1SYNC R/W-0 R/W-0 bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset
T1CKPS1 T1CKPS0 T1OSCEN
TMR1CS TMR1ON
bit 7-6: Unimplemented: Read as '0' bit 5-4: T1CKPS1:T1CKPS0: Timer1 Input Clock Prescale Select bits 11 = 1:8 Prescale value 10 = 1:4 Prescale value 01 = 1:2 Prescale value 00 = 1:1 Prescale value bit 3: T1OSCEN: Timer1 Oscillator Enable Control bit 1 = Oscillator is enabled (TRISC<1:0> ignored) 0 = Oscillator is shut off (The oscillator is turned off to reduce power drain T1SYNC: Timer1 External Clock Input Synchronization Control bit TMR1CS = 1 1 = Do not synchronize external clock input 0 = Synchronize external clock input TMR1CS = 0 This bit is ignored. Timer1 uses the internal clock when TMR1CS = 0. TMR1CS: Timer1 Clock Source Select bit 1 = External clock from pin RC0/T1OSO/T1CKI (on the rising edge) 0 = Internal clock (FOSC/4) TMR1ON: Timer1 On bit 1 = Enables Timer1 0 = Stops Timer1
bit 2:
bit 1:
bit 0:
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 27
PIC16C62B/72A
FIGURE 5-1: TIMER1 BLOCK DIAGRAM
Set flag bit TMR1IF on Overflow TMR1H
TMR1 TMR1L
0 1 TMR1ON on/off T1SYNC
Synchronized clock input
T1OSC RC0/T1OSO/T1CKI T1OSCEN FOSC/4 Enable Internal Oscillator(1) Clock 1 Prescaler 1, 2, 4, 8 0 2 T1CKPS1:T1CKPS0 TMR1CS SLEEP input Synchronize det
RC1/T1OSI
Note 1: When the T1OSCEN bit is cleared, the inverter and feedback resistor are turned off. This eliminates power drain.
DS35008B-page 28
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
5.2 Timer1 Oscillator 5.3 Timer1 Interrupt
A crystal oscillator circuit is built-in between pins T1OSI (input) and T1OSO (amplifier output). It is enabled by setting control bit T1OSCEN (T1CON<3>). When the Timer1 oscillator is enabled, RC0 and RC1 pins become T1OSO and T1OSI inputs, overriding TRISC<1:0>. The oscillator is a low power oscillator rated up to 200 kHz. It will continue to run during SLEEP. It is primarily intended for a 32 kHz crystal. Table 5-1 shows the capacitor selection for the Timer1 oscillator. The Timer1 oscillator is identical to the LP oscillator. The user must provide a software time delay to ensure proper oscillator start-up. The TMR1 Register pair (TMR1H:TMR1L) increments from 0000h to FFFFh and rolls over to 0000h. The TMR1 Interrupt, if enabled, is generated on overflow and is latched in interrupt flag bit TMR1IF (PIR1<0>). This interrupt can be enabled by setting TMR1 interrupt enable bit TMR1IE (PIE1<0>).
5.4
Resetting Timer1 using a CCP Trigger Output
If the CCP module is configured in compare mode to generate a "special event trigger" (CCP1M3:CCP1M0 = 1011), this signal will reset Timer1 and start an A/D conversion (if the A/D module is enabled). Note: The special event trigger from the CCP1 module will not set interrupt flag bit TMR1IF (PIR1<0>).
TABLE 5-1
Osc Type LP
CAPACITOR SELECTION FOR THE TIMER1 OSCILLATOR
Freq 32 kHz 100 kHz 200 kHz C1 33 pF 15 pF 15 pF C2 33 pF 15 pF 15 pF
Timer1 must be configured for either timer or synchronized counter mode to take advantage of this feature. If Timer1 is running in asynchronous counter mode, this reset operation may not work. In the event that a write to Timer1 coincides with a special event trigger from CCP1, the write will take precedence. In this mode of operation, the CCPR1H:CCPR1L registers pair effectively becomes the period register for Timer1.
These values are for design guidance only.
Crystals Tested: 32.768 kHz Epson C-001R32.768K-A 20 PPM 100 kHz Epson C-2 100.00 KC-P 20 PPM 200 kHz STD XTL 200.000 kHz 20 PPM Note 1: Higher capacitance increases the stability of oscillator but also increases the start-up time. 2: Since each resonator/crystal has its own characteristics, the user should consult the resonator/crystal manufacturer for appropriate values of external components.
TABLE 5-2
Address Name 0Bh,8Bh 0Ch 8Ch 0Eh 0Fh 10h Legend:
REGISTERS ASSOCIATED WITH TIMER1 AS A TIMER/COUNTER
Bit 7 GIE -- -- Bit 6 PEIE ADIF ADIE Bit 5 T0IE -- -- Bit 4 INTE -- -- Bit 3 RBIE SSPIF SSPIE Bit 2 T0IF CCP1IF CCP1IE Bit 1 INTF TMR2IF TMR2IE Bit 0 RBIF TMR1IF TMR1IE Value on POR, BOR Value on all other resets
INTCON PIR1 PIE1 TMR1L TMR1H T1CON
0000 000x 0000 000u -0-- 0000 -0-- 0000 -0-- 0000 -0-- 0000 xxxx xxxx uuuu uuuu xxxx xxxx uuuu uuuu
Holding register for the Least Significant Byte of the 16-bit TMR1 register Holding register for the Most Significant Byte of the 16-bit TMR1 register -- --
T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON --00 0000 --uu uuuu
x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by the Timer1 module.
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 29
PIC16C62B/72A
NOTES:
DS35008B-page 30
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
6.0 TIMER2 MODULE
The Timer2 module timer has the following features: * 8-bit timer (TMR2 register) - Readable and writable * 8-bit period register (PR2) - Readable and writable * Software programmable prescaler (1:1, 1:4, 1:16) * Software programmable postscaler (1:1 to 1:16) * Interrupt on match (TMR2 = PR2) * Timer2 can be used by SSP and CCP Timer2 has a control register, shown in Register 6-1. Timer2 can be shut off by clearing control bit TMR2ON (T2CON<2>) to minimize power consumption. Figure 6-1 is a simplified block diagram of the Timer2 module. Additional information on timer modules is available in the PICmicroTM Mid-Range Reference Manual, (DS33023).
FIGURE 6-1:
Sets flag bit TMR2IF
TIMER2 BLOCK DIAGRAM
TMR2 output (1) Reset Prescaler 1:1, 1:4, 1:16 2
TMR2 reg Comparator
FOSC/4
Postscaler 1:1 to 1:16 4
EQ
PR2 reg
Note 1: TMR2 register output can be software selected by the SSP Module as a baud clock.
REGISTER 6-1:T2CON: TIMER2 CONTROL REGISTER (ADDRESS 12h)
U-0 -- bit7 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 R/W-0 bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset
TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON
T2CKPS1 T2CKPS0
bit 7: bit 6-3:
Unimplemented: Read as '0' TOUTPS3:TOUTPS0: Timer2 Output Postscale Select bits 0000 = 1:1 Postscale 0001 = 1:2 Postscale 0010 = 1:3 Postscale * * * 1111 = 1:16 Postscale TMR2ON: Timer2 On bit 1 = Timer2 is on 0 = Timer2 is off T2CKPS1:T2CKPS0: Timer2 Clock Prescale Select bits 00 = Prescaler is 1 01 = Prescaler is 4 1x = Prescaler is 16
bit 2:
bit 1-0:
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 31
PIC16C62B/72A
6.1 Timer2 Operation 6.2 Timer2 Interrupt
The Timer2 output is also used by the CCP module to generate the PWM "On-Time", and the PWM period with a match with PR2. The TMR2 register is readable and writable, and is cleared on any device reset. The input clock (FOSC/4) has a prescale option of 1:1, 1:4 or 1:16, selected by control bits T2CKPS1:T2CKPS0 (T2CON<1:0>). The match output of TMR2 goes through a 4-bit postscaler (which gives a 1:1 to 1:16 scaling) to generate a TMR2 interrupt (latched in flag bit TMR2IF, (PIR1<1>)). The prescaler and postscaler counters are cleared when any of the following occurs: * a write to the TMR2 register * a write to the T2CON register * any device reset (Power-on Reset, MCLR reset, Watchdog Timer reset or Brown-out Reset) TMR2 is not cleared when T2CON is written. The Timer2 module has an 8-bit period register PR2. Timer2 increments from 00h until it matches PR2 and then resets to 00h on the next increment cycle. PR2 is a readable and writable register. The PR2 register is initialized to FFh upon reset.
6.3
Output of TMR2
The output of TMR2 (before the postscaler) is fed to the Synchronous Serial Port module, which optionally uses it to generate shift clock.
TABLE 6-1
Address 0Bh,8Bh 0Ch 8Ch 11h 12h 92h Legend: Name INTCON PIR1 PIE1 TMR2 T2CON PR2
REGISTERS ASSOCIATED WITH TIMER2 AS A TIMER/COUNTER
Bit 7 GIE -- -- Bit 6 PEIE ADIF ADIE Bit 5 T0IE -- -- Bit 4 INTE -- -- Bit 3 RBIE SSPIF SSPIE Bit 2 T0IF CCP1IF CCP1IE Bit 1 INTF TMR2IF TMR2IE Bit 0 RBIF TMR1IF TMR1IE Value on POR, BOR Value on all other resets
0000 000x 0000 000u -00- 0000 0000 0000 -0-- 0000 0000 0000 0000 0000 0000 0000
Timer2 module's register -- TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1
T2CKPS0 -000 0000 -000 0000 1111 1111 1111 1111
Timer2 Period Register
x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by the Timer2 module.
DS35008B-page 32
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
7.0 CAPTURE/COMPARE/PWM (CCP) MODULE
Additional information on the CCP module is available in the PICmicroTM Mid-Range Reference Manual, (DS33023).
The CCP (Capture/Compare/PWM) module contains a 16-bit register, which can operate as a 16-bit capture register, as a 16-bit compare register or as a PWM master/slave duty cycle register. Table 7-1 shows the timer resources of the CCP module modes. Capture/Compare/PWM Register 1 (CCPR1) is comprised of two 8-bit registers: CCPR1L (low byte) and CCPR1H (high byte). The CCP1CON register controls the operation of CCP1. All are readable and writable.
TABLE 7-1
CCP MODE - TIMER RESOURCE
Timer Resource Timer1 Timer1 Timer2
CCP Mode Capture Compare PWM
TABLE 7-2
INTERACTION OF TWO CCP MODULES
Interaction Same TMR1 time-base. The compare should be configured for the special event trigger, which clears TMR1. The compare(s) should be configured for the special event trigger, which clears TMR1. The PWMs will have the same frequency and update rate (TMR2 interrupt). None. None.
CCPx Mode CCPy Mode Capture Capture Compare PWM PWM PWM Capture Compare Compare PWM Capture Compare
REGISTER 7-1:CCP1CON REGISTER (ADDRESS 17h)
U-0 -- bit7 U-0 -- R/W-0 R/W-0 R/W-0 CCP1X CCP1Y CCP1M3 R/W-0 CCP1M2 R/W-0 R/W-0 CCP1M1 CCP1M0 bit0
R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n =Value at POR reset
bit 7-6: Unimplemented: Read as '0' bit 5-4: CCP1X:CCP1Y: PWM Least Significant bits Capture Mode: Unused Compare Mode: Unused PWM Mode: These bits are the two LSbs of the PWM duty cycle. The eight MSbs are found in CCPR1L. bit 3-0: CCP1M3:CCP1M0: CCP1 Mode Select bits 0000 = Capture/Compare/PWM off (resets CCP1 module) 0100 = Capture mode, every falling edge 0101 = Capture mode, every rising edge 0110 = Capture mode, every 4th rising edge 0111 = Capture mode, every 16th rising edge 1000 = Compare mode, set output on match (CCP1IF bit is set) 1001 = Compare mode, clear output on match (CCP1IF bit is set) 1010 = Compare mode, generate software interrupt on match (CCP1IF bit is set, CCP1 pin is unaffected) 1011 = Compare mode, trigger special event (CCP1IF bit is set; CCP1 resets TMR1 and starts an A/D conversion (if A/D module is enabled)) 11xx = PWM mode
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 33
PIC16C62B/72A
7.1 Capture Mode
7.1.4 CCP PRESCALER In Capture mode, CCPR1H:CCPR1L captures the 16-bit value of the TMR1 register, when an event occurs on pin RC2/CCP1. An event is defined as: * * * * every falling edge every rising edge every 4th rising edge every 16th rising edge There are four prescaler settings, specified by bits CCP1M3:CCP1M0. Whenever the CCP module is turned off, or the CCP module is not in capture mode, the prescaler counter is cleared. This means that any reset will clear the prescaler counter. Switching from one capture prescaler to another may generate an interrupt. Also, the prescaler counter will not be cleared, therefore the first capture may be from a non-zero prescaler. Example 7-1 shows the recommended method for switching between capture prescalers. This example also clears the prescaler counter and will not generate the "false" interrupt.
An event is selected by control bits CCP1M3:CCP1M0 (CCP1CON<3:0>). When a capture is made, the interrupt request flag bit ,CCP1IF (PIR1<2>), is set. It must be cleared in software. If another capture occurs before the value in register CCPR1 is read, the old captured value will be lost.
EXAMPLE 7-1:
CLRF MOVLW
CHANGING BETWEEN CAPTURE PRESCALERS
;Turn CCP module off ;Load the W reg with ; the new prescaler ; mode value and CCP ON ;Load CCP1CON with this ; value
FIGURE 7-1:
CAPTURE MODE OPERATION BLOCK DIAGRAM
Set flag bit CCP1IF (PIR1<2>)
CCP1CON NEW_CAPT_PS
Prescaler / 1, 4, 16 RC2/CCP1 Pin and edge detect
MOVWF
CCPR1L
CCP1CON
CCPR1H Capture Enable TMR1H CCP1CON<3:0> Q's
TMR1L
7.1.1
CCP PIN CONFIGURATION
In Capture mode, the RC2/CCP1 pin should be configured as an input by setting the TRISC<2> bit. Note: If the RC2/CCP1 is configured as an output, a write to the port can cause a capture condition. TIMER1 MODE SELECTION
7.1.2
Timer1 must be running in timer mode or synchronized counter mode for the CCP module to use the capture feature. In asynchronous counter mode, the capture operation may not work consistently. 7.1.3 SOFTWARE INTERRUPT
When the Capture mode is changed, a false capture interrupt may be generated. The user should clear CCP1IE (PIE1<2>) before changing the capture mode to avoid false interrupts. Clear the interrupt flag bit, CCP1IE before setting CCP1IE.
DS35008B-page 34
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
7.2 Compare Mode
7.2.1 CCP PIN CONFIGURATION In Compare mode, the 16-bit CCPR1 register value is constantly compared against the TMR1 register pair value. When a match occurs, the RC2/CCP1 pin is: * driven High * driven Low * remains Unchanged The action on the pin is based on the value of control bits CCP1M3:CCP1M0 (CCP1CON<3:0>). The interrupt flag bit, CCP1IF, is set on all compare matches. The user must configure the RC2/CCP1 pin as an output by clearing the TRISC<2> bit. Note: Clearing the CCP1CON register will force the RC2/CCP1 compare output latch to the default low level. This is not the data latch. TIMER1 MODE SELECTION
7.2.2
FIGURE 7-2:
COMPARE MODE OPERATION BLOCK DIAGRAM
Timer1 must be running in Timer mode or Synchronized Counter mode if the CCP module is using the compare feature. In Asynchronous Counter mode, the compare operation may not work. 7.2.3 SOFTWARE INTERRUPT MODE
Special event trigger will: reset Timer1, but not set interrupt flag bit TMR1IF (PIR1<0>), and set bit GO/DONE (ADCON0<2>), which starts an A/D conversion Special Event Trigger Set flag bit CCP1IF (PIR1<2>) CCPR1H CCPR1L Output Logic match RC2/CCP1 R Pin TRISC<2> Output Enable CCP1CON<3:0> Mode Select Q S Comparator TMR1H TMR1L
When a generated software interrupt is chosen, the CCP1 pin is not affected. Only a CCP interrupt is generated (if enabled). 7.2.4 SPECIAL EVENT TRIGGER
In this mode, an internal hardware trigger is generated, which may be used to initiate an action. The special event trigger output of CCP1 resets the TMR1 register pair. This allows the CCPR1 register to effectively be a 16-bit programmable period register for Timer1. The special trigger output of CCP1 resets the TMR1 register pair and starts an A/D conversion (if the A/D module is enabled).
TABLE 7-3
Address
0Bh,8Bh 0Ch 8Ch 87h 0Eh 0Fh 10h 15h 16h 17h
REGISTERS ASSOCIATED WITH CAPTURE, COMPARE, AND TIMER1
Bit 7
GIE -- --
Name
INTCON PIR1 PIE1 TRISC TMR1L TMR1H T1CON CCPR1L CCPR1H CCP1CON
Bit 6
PEIE ADIF ADIE
Bit 5
T0IE -- --
Bit 4
INTE -- --
Bit 3
RBIE SSPIF SSPIE
Bit 2
T0IF CCP1IF CCP1IE
Bit 1
INTF TMR2IF TMR2IE
Bit 0
RBIF
Value on POR, BOR
Value on all other resets
0000 000x 0000 000u
TMR1IF -0-- 0000 -0-- 0000 TMR1IE -0-- 0000 -0-- 0000 1111 1111 1111 1111 xxxx xxxx uuuu uuuu xxxx xxxx uuuu uuuu
PORTC Data Direction Register Holding register for the Least Significant Byte of the 16-bit TMR1 register Holding register for the Most Significant Byte of the 16-bit TMR1register -- --
T1CKPS1 T1CKPS0 T1OSCEN T1SYNC TMR1CS TMR1ON --00 0000 --uu uuuu xxxx xxxx uuuu uuuu xxxx xxxx uuuu uuuu CCP1M3 CCP1M2 CCP1M1 CCP1M0 --00 0000 --00 0000
Capture/Compare/PWM register1 (LSB) Capture/Compare/PWM register1 (MSB) -- -- CCP1X CCP1Y
Legend:
x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by Capture and Timer1.
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 35
PIC16C62B/72A
7.3 PWM Mode
7.3.1 PWM PERIOD In Pulse Width Modulation (PWM) mode, the CCP1 pin produces up to a 10-bit resolution PWM output. Since the CCP1 pin is multiplexed with the PORTC data latch, the TRISC<2> bit must be cleared to make the CCP1 pin an output. Note: Clearing the CCP1CON register will force the CCP1 PWM output latch to the default low level. This is not the PORTC I/O data latch. The PWM period is specified by writing to the PR2 register. The PWM period can be calculated using the following formula: PWM period = [(PR2) + 1] * 4 * TOSC * (TMR2 prescale value) PWM frequency is defined as 1 / [PWM period]. When TMR2 is equal to PR2, the following three events occur on the next increment cycle: * TMR2 is cleared * The CCP1 pin is set (exception: if PWM duty cycle = 0%, the CCP1 pin will not be set) * The PWM duty cycle is latched from CCPR1L into CCPR1H Note: The Timer2 postscaler (see Section 6.0) is not used in the determination of the PWM frequency. The postscaler could be used to have a servo update rate at a different frequency than the PWM output. PWM ON-TIME
Figure 7-3 shows a simplified block diagram of the CCP module in PWM mode. For a step by step procedure on how to set up the CCP module for PWM operation, see Section 7.3.3.
FIGURE 7-3:
SIMPLIFIED PWM BLOCK DIAGRAM
CCP1CON<5:4>
Duty Cycle Registers CCPR1L
7.3.2
CCPR1H (Slave) Q RC2/CCP1 TMR2 (Note 1) S TRISC<2> Clear Timer, CCP1 pin and latch D.C.
Comparator
R
The PWM on-time is specified by writing to the CCPR1L register and to the CCP1CON<5:4> bits. Up to 10-bit resolution is available. CCPR1L contains eight MSbs and CCP1CON<5:4> contains two LSbs. This 10-bit value is represented by CCPR1L:CCP1CON<5:4>. The following equation is used to calculate the PWM duty cycle in time: PWM on-time = (CCPR1L:CCP1CON<5:4>) * Tosc * (TMR2 prescale value) CCPR1L and CCP1CON<5:4> can be written to at any time, but the on-time value is not latched into CCPR1H until after a match between PR2 and TMR2 occurs (i.e., the period is complete). In PWM mode, CCPR1H is a read-only register. The CCPR1H register and a 2-bit internal latch are used to double buffer the PWM on-time. This double buffering is essential for glitchless PWM operation. When the CCPR1H and 2-bit latch match TMR2 concatenated with an internal 2-bit Q clock or 2 bits of the TMR2 prescaler, the CCP1 pin is cleared. Maximum PWM resolution (bits) for a given PWM frequency:
log ( Fosc Fpwm ) bits log(2)
Comparator
PR2
Note 1: 8-bit timer is concatenated with 2-bit internal Q clock or 2 bits of the prescaler to create 10-bit time-base.
A PWM output (Figure 7-4) has a time base (period) and a time that the output stays high (on-time). The frequency of the PWM is the inverse of the period (1/period).
FIGURE 7-4:
PWM OUTPUT
Period
On-Time TMR2 = PR2
Resolution =
Note:
TMR2 = Duty Cycle TMR2 = PR2
If the PWM on-time value is larger than the PWM period, the CCP1 pin will not be cleared.
For an example PWM period and on-time calculation, see the PICmicroTM Mid-Range Reference Manual, (DS33023).
DS35008B-page 36
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
7.3.3 SET-UP FOR PWM OPERATION The following steps should be taken when configuring the CCP module for PWM operation: 1. 2. 3. 4. 5. Set the PWM period by writing to the PR2 register. Set the PWM on-time by writing to the CCPR1L register and CCP1CON<5:4> bits. Make the CCP1 pin an output by clearing the TRISC<2> bit. Set the TMR2 prescale value and enable Timer2 by writing to T2CON. Configure the CCP1 module for PWM operation.
TABLE 7-4
EXAMPLE PWM FREQUENCIES AND RESOLUTIONS AT 20 MHz
PWM Frequency 1.22 kHz 4.88 kHz 19.53 kHz 78.12 kHz 156.3 kHz 208.3 kHz 16 0xFF 10 4 0xFF 10 1 0xFF 10 1 0x3F 8 1 0x1F 7 1 0x17 5.5
Timer Prescaler (1, 4, 16) PR2 Value Maximum Resolution (bits)
TABLE 7-5
Address 0Bh,8Bh 0Ch 8Ch Name
REGISTERS ASSOCIATED WITH PWM AND TIMER2
Bit 7 GIE -- -- Bit 6 PEIE ADIF ADIE Bit 5 T0IE -- -- Bit 4 INTE -- -- Bit 3 RBIE SSPIF SSPIE Bit 2 T0IF CCP1IF CCP1IE Bit 1 INTF TMR2IF TMR2IE Bit 0 RBIF TMR1IF TMR1IE Value on POR, BOR Value on all other resets
INTCON PIR1 PIE1
0000 000x 0000 000u -0-- 0000 -0-- 0000 -0-- 0000 -0-- 0000
87h
11h 92h 12h 15h 16h 17h Legend:
TRISC
TMR2 PR2 T2CON CCPR1L CCPR1H CCP1CON
PORTC Data Direction Register
Timer2 module's register Timer2 module's period register --
1111 1111 1111 1111
0000 0000 0000 0000 1111 1111 1111 1111
TOUTPS3 TOUTPS2 TOUTPS1 TOUTPS0 TMR2ON T2CKPS1 T2CKPS0 -000 0000 -000 0000 xxxx xxxx uuuu uuuu xxxx xxxx uuuu uuuu CCP1M3 CCP1M2 CCP1M1 CCP1M0 --00 0000 --00 0000
Capture/Compare/PWM register1 (LSB) Capture/Compare/PWM register1 (MSB) -- -- CCP1X CCP1Y
x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by PWM and Timer2.
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 37
PIC16C62B/72A
NOTES:
DS35008B-page 38
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
8.0
8.1
SYNCHRONOUS SERIAL PORT (SSP) MODULE
SSP Module Overview
ister, and then set bit SSPEN. This configures the SDI, SDO, SCK and SS pins as serial port pins. For the pins to behave as the serial port function, they must have their data direction bits (in the TRISC register) appropriately programmed. That is: * SDI must have TRISC<4> set * SDO must have TRISC<5> cleared * SCK (master operation) must have TRISC<3> cleared * SCK (Slave mode) must have TRISC<3> set * SS must have TRISA<5> set (if used) Note: When the SPI is in Slave Mode with SS pin control enabled, (SSPCON<3:0> = 0100) the SPI module will reset if the SS pin is set to VDD. If the SPI is used in Slave Mode with CKE = '1', then the SS pin control must be enabled.
The Synchronous Serial Port (SSP) module is a serial interface useful for communicating with other peripheral or microcontroller devices. These peripheral devices may be Serial EEPROMs, shift registers, display drivers, A/D converters, etc. The SSP module can operate in one of two modes: * Serial Peripheral Interface (SPI) * Inter-Integrated Circuit (I2C) For more information on SSP operation (including an I2C Overview), refer to the PICmicroTM Mid-Range Reference Manual, (DS33023). Also, refer to Application Note AN578, "Use of the SSP Module in the I 2C MultiMaster Environment."
Note:
8.2
SPI Mode
This section contains register definitions and operational characteristics of the SPI module. Additional information on SPI operation may be found in the PICmicroTM Mid-Range Reference Manual, (DS33023). 8.2.1 OPERATION OF SSP MODULE IN SPI MODE
FIGURE 8-1:
SSP BLOCK DIAGRAM (SPI MODE)
Internal Data Bus Read SSPBUF reg Write
A block diagram of the SSP Module in SPI Mode is shown in Figure 8-1. The SPI mode allows 8-bits of data to be synchronously transmitted and received simultaneously. To accomplish communication, three pins are used: * Serial Data Out (SDO)RC5/SDO * Serial Data In (SDI)RC4/SDI/SDA * Serial Clock (SCK)RC3/SCK/SCL Additionally, a fourth pin may be used when in a slave mode of operation: * Slave Select (SS)RA5/SS/AN4 When initializing the SPI, several options need to be specified. This is done by programming the appropriate control bits in the SSPCON register (SSPCON<5:0>) and SSPSTAT<7:6>. These control bits allow the following to be specified: Master Operation (SCK is the clock output) Slave Mode (SCK is the clock input) Clock Polarity (Idle state of SCK) Clock Edge (Output data on rising/falling edge of SCK) * Clock Rate (master operation only) * Slave Select Mode (Slave mode only) To enable the serial port, SSP Enable bit, SSPEN (SSPCON<5>) must be set. To reset or reconfigure SPI mode, clear bit SSPEN, re-initialize the SSPCON reg* * * *
SSPSR reg RC4/SDI/SDA RC5/SDO bit0 Shift Clock
SS Control Enable RA5/SS/AN4 Edge Select 2 Clock Select SSPM3:SSPM0 4 Edge Select RC3/SCK/ SCL TRISC<3>
TMR2 output 2 Prescaler TCY 4, 16, 64
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 39
PIC16C62B/72A
TABLE 8-1
Address 0Bh,8Bh 0Ch 8Ch 13h 14h 94h 85h 87h Name INTCON PIR1 PIE1 SSPBUF
REGISTERS ASSOCIATED WITH SPI OPERATION
Bit 7 GIE
-- --
Bit 6 PEIE ADIF ADIE
Bit 5 T0IE -- --
Bit 4 INTE -- --
Bit 3 RBIE SSPIF SSPIE
Bit 2 T0IF
Bit 1 INTF
Bit 0 RBIF
Value on POR, BOR
Value on all other resets
0000 000x 0000 000u
CCP1IF TMR2IF TMR1IF -0-- 0000 -0-- 0000 CCP1IE TMR2IE TMR1IE -0-- 0000 -0-- 0000 xxxx xxxx uuuu uuuu SSPM1 UA SSPM0 BF 0000 0000 0000 0000 0000 0000 0000 0000 --11 1111 --11 1111 1111 1111 1111 1111
Synchronous Serial Port Receive Buffer/Transmit Register SSPOV SSPEN CKE -- D/A CKP P SSPM3 S SSPM2 R/W
SSPCON WCOL SSPSTAT TRISA TRISC SMP --
PORTA Data Direction Register
PORTC Data Direction Register
Legend: x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used by the SSP in SPI mode.
DS35008B-page 40
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
8.3 SSP I 2C Operation
The SSP module in I 2C mode fully implements all slave functions, except general call support, and provides interrupts on start and stop bits in hardware to support firmware implementations of the master functions. The SSP module implements the standard mode specifications, as well as 7-bit and 10-bit addressing. Two pins are used for data transfer. These are the RC3/SCK/SCL pin, which is the clock (SCL), and the RC4/SDI/SDA pin, which is the data (SDA). The user must configure these pins as inputs or outputs through the TRISC<4:3> bits. The SSP module functions are enabled by setting SSP Enable bit SSPEN (SSPCON<5>). The SSPCON register allows control of the I 2C operation. Four mode selection bits (SSPCON<3:0>) allow one of the following I 2C modes to be selected: * I 2C Slave mode (7-bit address) * I 2C Slave mode (10-bit address) * I 2C Slave mode (7-bit address), with start and stop bit interrupts enabled for firmware master mode support * I 2C Slave mode (10-bit address), with start and stop bit interrupts enabled for firmware master mode support * I 2C start and stop bit interrupts enabled for firmware master mode support, slave mode idle Selection of any I 2C mode, with the SSPEN bit set, forces the SCL and SDA pins to be operated as open drain outputs, provided these pins are programmed to inputs by setting the appropriate TRISC bits. Additional information on SSP I2C operation may be found in the PICmicroTM Mid-Range Reference Manual, (DS33023). 8.3.1 SLAVE MODE
FIGURE 8-2:
SSP BLOCK DIAGRAM (I2C MODE)
Internal Data Bus Read SSPBUF reg shift clock SSPSR reg Write
RC3/SCK/SCL
In slave mode, the SCL and SDA pins must be configured as inputs (TRISC<4:3> set). The SSP module will override the input state with the output data when required (slave-transmitter). When an address is matched or the data transfer after an address match is received, the hardware automatically will generate the acknowledge (ACK) pulse, and load the SSPBUF register with the received value in the SSPSR register. There are certain conditions that will cause the SSP module not to give this ACK pulse. This happens if either of the following conditions occur:
Set, Reset S, P bits (SSPSTAT reg)
RC4/ SDI/ SDA
MSb
LSb Addr Match
Match detect
SSPADD reg Start and Stop bit detect
a) b)
The SSP module has five registers for These are the: * * * * *
I2C
operation.
The buffer full bit BF (SSPSTAT<0>) was set before the transfer was completed. The overflow bit SSPOV (SSPCON<6>) was set before the transfer was completed.
SSP Control Register (SSPCON) SSP Status Register (SSPSTAT) Serial Receive/Transmit Buffer (SSPBUF) SSP Shift Register (SSPSR) - Not accessible SSP Address Register (SSPADD)
In this case, the SSPSR register value is not loaded into the SSPBUF, but bit SSPIF (PIR1<3>) is set. Table 8-2 shows what happens when a data transfer byte is received, given the status of bits BF and SSPOV. The shaded cells show the condition where user software did not properly clear the overflow condition. Flag bit BF is cleared by reading the SSPBUF register, while bit SSPOV is cleared through software. The SCL clock input must have a minimum high and low for proper operation. The high and low times of the I2C specification, as well as the requirement of the SSP module, is shown in timing parameter #100, THIGH, and parameter #101, TLOW.
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 41
PIC16C62B/72A
8.3.1.1 ADDRESSING Once the SSP module has been enabled, it waits for a START condition to occur. Following the START condition, 8 bits are shifted into the SSPSR register. All incoming bits are sampled with the rising edge of the clock (SCL) line. The value of register SSPSR<7:1> is compared to the value of the SSPADD register. The address is compared on the falling edge of the eighth clock (SCL) pulse. If the addresses match and the BF and SSPOV bits are clear, the following events occur: a) b) c) d) The SSPSR register value is loaded into the SSPBUF register. The buffer full bit, BF is set. An ACK pulse is generated. SSP interrupt flag bit, SSPIF (PIR1<3>), is set (interrupt is generated if enabled) on the falling edge of the ninth SCL pulse. `1111 0 A9 A8 0', where A9 and A8 are the two MSbs of the address. The sequence of events for 10-bit address is as follows, with steps 7- 9 for slave-transmitter: 1. 2. Receive first (high) byte of Address (bits SSPIF, BF, and bit UA (SSPSTAT<1>) are set). Update the SSPADD register with second (low) byte of Address (clears bit UA and releases the SCL line). Read the SSPBUF register (clears bit BF) and clear flag bit SSPIF. Receive second (low) byte of Address (bits SSPIF, BF, and UA are set). Update the SSPADD register with the first (high) byte of Address, if match releases SCL line, this will clear bit UA. Read the SSPBUF register (clears bit BF) and clear flag bit SSPIF. Receive repeated START condition. Receive first (high) byte of Address (bits SSPIF and BF are set). Read the SSPBUF register (clears bit BF) and clear flag bit SSPIF.
3. 4. 5.
6. 7. 8. 9.
In 10-bit address mode, two address bytes need to be received by the slave. The five Most Significant bits (MSbs) of the first address byte specify if this is a 10-bit address. Bit R/W (SSPSTAT<2>) must specify a write so the slave device will receive the second address byte. For a 10-bit address, the first byte would equal
TABLE 8-2
DATA TRANSFER RECEIVED BYTE ACTIONS
Set bit SSPIF (SSP Interrupt occurs if enabled) Yes Yes Yes Yes
Status Bits as Data Transfer is Received BF 0 1 1 0 SSPOV 0 0 1 1 SSPSR SSPBUF Yes No No Yes Generate ACK Pulse Yes No No No
Note: Shaded cells show the conditions where the user software did not properly clear the overflow condition.
DS35008B-page 42
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
8.3.1.2 RECEPTION When the R/W bit of the address byte is clear and an address match occurs, the R/W bit of the SSPSTAT register is cleared. The received address is loaded into the SSPBUF register. When the address byte overflow condition exists, then no acknowledge (ACK) pulse is given. An overflow condition is defined as either bit BF (SSPSTAT<0>) is set or bit SSPOV (SSPCON<6>) is set. An SSP interrupt is generated for each data transfer byte. Flag bit SSPIF (PIR1<3>) must be cleared in software. The SSPSTAT register is used to determine the status of the byte.
FIGURE 8-3:
I 2C WAVEFORMS FOR RECEPTION (7-BIT ADDRESS)
SDA
Receiving Address Receiving Data R/W=0 Receiving Data ACK ACK ACK A7 A6 A5 A4 A3 A2 A1 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 S 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 1 2 3 4 5 6 7 8 9 P
SCL
SSPIF (PIR1<3>)
Cleared in software
Bus Master terminates transfer
BF (SSPSTAT<0>)
SSPBUF register is read
SSPOV (SSPCON<6>) Bit SSPOV is set because the SSPBUF register is still full. ACK is not sent.
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 43
PIC16C62B/72A
8.3.1.3 TRANSMISSION When the R/W bit of the incoming address byte is set and an address match occurs, the R/W bit of the SSPSTAT register is set. The received address is loaded into the SSPBUF register. The ACK pulse will be sent on the ninth bit and the CKP will be cleared by hardware, holding SCL low. Slave devices cause the master to wait by holding the SCL line low. The transmit data is loaded into the SSPBUF register, which in turn loads the SSPSR register. When bit CKP (SSPCON<4>) is set, pin RC3/SCK/SCL releases SCL. When the SCL line goes high, the master may resume operating the SCL line and receiving data. The master must monitor the SCL pin prior to asserting another clock pulse. The slave devices may be holding off the master by stretching the clock. The eight data bits are shifted out on the falling edge of the SCL input. This ensures that the SDA signal is valid during the SCL high time (Figure 8-4). An SSP interrupt is generated for each data transfer byte. Flag bit SSPIF must be cleared in software, and the SSPSTAT register used to determine the status of the byte. Flag bit SSPIF is set on the falling edge of the ninth clock pulse. As a slave-transmitter, the ACK pulse from the masterreceiver is latched on the rising edge of the ninth SCL input pulse. If the SDA line was high (not ACK), then the data transfer is complete. When the ACK is latched by the slave, the slave logic is reset (resets SSPSTAT register) and the slave then monitors for another occurrence of the START bit. If the SDA line was low (ACK), the transmit data must be loaded into the SSPBUF register, which also loads the SSPSR register. Then pin RC3/SCK/SCL should be enabled by setting bit CKP.
FIGURE 8-4:
I 2C WAVEFORMS FOR TRANSMISSION (7-BIT ADDRESS)
Receiving Address R/W = 1 A1 ACK D7 D6 D5 D4 Transmitting Data D3 D2 D1 D0 ACK
SDA
A7
A6
A5
A4
A3
A2
SCL
S
1 2 Data in sampled
3
4
5
6
7
8
9
1 SCL held low while CPU responds to SSPIF
2
3
4
5
6
7
8
9
P
SSPIF (PIR1<3>) BF (SSPSTAT<0>)
cleared in software
SSPBUF is written in software CKP (SSPCON<4>)
From SSP interrupt service routine
Set bit after writing to SSPBUF (the SSPBUF must be written-to before the CKP bit can be set)
DS35008B-page 44
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
8.3.2 MASTER OPERATION 8.3.3 MULTI-MASTER OPERATION Master operation is supported in firmware using interrupt generation on the detection of the START and STOP conditions. The STOP (P) and START (S) bits are cleared by a reset or when the SSP module is disabled. The STOP (P) and START (S) bits will toggle based on the START and STOP conditions. Control of the I 2C bus may be taken when the P bit is set, or the bus is idle and both the S and P bits are clear. In master operation, the SCL and SDA lines are manipulated in software by clearing the corresponding TRISC<4:3> bit(s). The output level is always low, irrespective of the value(s) in PORTC<4:3>. So when transmitting data, a '1' data bit must have the TRISC<4> bit set (input) and a '0' data bit must have the TRISC<4> bit cleared (output). The same scenario is true for the SCL line with the TRISC<3> bit. The following events will cause SSP Interrupt Flag bit, SSPIF, to be set (SSP Interrupt if enabled): * START condition * STOP condition * Byte transfer completed Master operation can be done with either the slave mode idle (SSPM3:SSPM0 = 1011) or with the slave active. When both master operation and slave modes are used, the software needs to differentiate the source(s) of the interrupt. For more information on master operation, see AN554 - Software Implementation of I2C Bus Master. In multi-master operation, the interrupt generation on the detection of the START and STOP conditions allows the determination of when the bus is free. The STOP (P) and START (S) bits are cleared from a reset or when the SSP module is disabled. The STOP (P) and START (S) bits will toggle based on the START and STOP conditions. Control of the I 2C bus may be taken when bit P (SSPSTAT<4>) is set, or the bus is idle and both the S and P bits clear. When the bus is busy, enabling the SSP Interrupt will generate the interrupt when the STOP condition occurs. In multi-master operation, the SDA line must be monitored to see if the signal level is the expected output level. This check only needs to be done when a high level is output. If a high level is expected and a low level is present, the device needs to release the SDA and SCL lines (set TRISC<4:3>). There are two stages where this arbitration can be lost, these are: * Address Transfer * Data Transfer When the slave logic is enabled, the slave continues to receive. If arbitration was lost during the address transfer stage, communication to the device may be in progress. If addressed, an ACK pulse will be generated. If arbitration was lost during the data transfer stage, the device will need to re-transfer the data at a later time. For more information on master operation, see AN578 - Use of the SSP Module in the of I2C Multi-Master Environment.
TABLE 8-3
Address Name
REGISTERS ASSOCIATED WITH I2C OPERATION
Bit 7 Bit 6 Bit 5 Bit 4 Bit 3 Bit 2 Bit 1 Bit 0 Value on POR, BOR 0000 000x -0-- 0000 -0-- 0000 xxxx xxxx 0000 0000 0000 0000 0000 0000 1111 1111 Value on all other resets 0000 000u -0-- 0000 -0-- 0000 uuuu uuuu 0000 0000 0000 0000 0000 0000 1111 1111
0Bh, 8Bh 0Ch 8Ch 13h 93h 14h 94h 87h
INTCON PIR1 PIE1
GIE -- --
PEIE ADIF ADIE
T0IE -- --
INTE -- --
RBIE
T0IF
INTF
RBIF
SSPIF CCP1IF TMR2IF TMR1IF SSPIE CCP1IE TMR2IE TMR1IE
SSPBUF Synchronous Serial Port Receive Buffer/Transmit Register SSPADD Synchronous Serial Port (I2C mode) Address Register SSPCON SSPSTAT TRISC WCOL SMP(1) SSPOV SSPEN CKE(1) D/A CKP P SSPM3 SSPM2 SSPM1 SSPM0 S R/W UA BF
PORTC Data Direction register
Legend: x = unknown, u = unchanged, - = unimplemented locations read as '0'. Shaded cells are not used by SSP module in SPI mode. Note 1: Maintain these bits clear in I2C mode.
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 45
PIC16C62B/72A
REGISTER 8-1: SSPSTAT: SYNC SERIAL PORT STATUS REGISTER (ADDRESS 94h)
R/W-0 R/W-0 SMP bit7 CKE
R-0 D/A
R-0 P
R-0 S
R-0 R/W
R-0 UA
R-0 BF bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n =Value at POR reset
bit 7:
SMP: SPI data input sample phase SPI Master Operation 1 = Input data sampled at end of data output time 0 = Input data sampled at middle of data output time SPI Slave Mode SMP must be cleared when SPI is used in slave mode I2C Mode This bit must be maintained clear CKE: SPI Clock Edge Select SPI Mode CKP = 0 1 = Data transmitted on rising edge of SCK 0 = Data transmitted on falling edge of SCK CKP = 1 1 = Data transmitted on falling edge of SCK 0 = Data transmitted on rising edge of SCK I2C Mode This bit must be maintained clear D/A: Data/Address bit (I2C mode only) 1 = Indicates that the last byte received or transmitted was data 0 = Indicates that the last byte received or transmitted was address P: Stop bit (I2C mode only. This bit is cleared when the SSP module is disabled, or when the Start bit is detected last, SSPEN is cleared) 1 = Indicates that a stop bit has been detected last (this bit is '0' on RESET) 0 = Stop bit was not detected last S: Start bit (I2C mode only. This bit is cleared when the SSP module is disabled, or when the Stop bit is detected last, SSPEN is cleared) 1 = Indicates that a start bit has been detected last (this bit is '0' on RESET) 0 = Start bit was not detected last R/W: Read/Write bit information (I2C mode only) This bit holds the R/W bit information following the last address match. This bit is only valid from the address match to the next start bit, stop bit, or ACK bit. 1 = Read 0 = Write UA: Update Address (10-bit I2C mode only) 1 = Indicates that the user needs to update the address in the SSPADD register 0 = Address does not need to be updated BF: Buffer Full Status bit Receive (SPI and I2C modes) 1 = Receive complete, SSPBUF is full 0 = Receive not complete, SSPBUF is empty Transmit (I2C mode only) 1 = Transmit in progress, SSPBUF is full 0 = Transmit complete, SSPBUF is empty
bit 6:
bit 5:
bit 4:
bit 3:
bit 2:
bit 1:
bit 0:
DS35008B-page 46
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
REGISTER 8-2: SSPCON: SYNC SERIAL PORT CONTROL REGISTER (ADDRESS 14h)
R/W-0 WCOL bit7
R/W-0 SSPOV
R/W-0 SSPEN
R/W-0 CKP
R/W-0 SSPM3
R/W-0 SSPM2
R/W-0 SSPM1
R/W-0 SSPM0 bit0 R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n =Value at POR reset
bit 7:
WCOL: Write Collision Detect bit 1 = The SSPBUF register is written while it is still transmitting the previous word (must be cleared in software) 0 = No collision SSPOV: Receive Overflow Indicator bit In SPI mode 1 = A new byte is received while the SSPBUF register is still holding the previous data. In case of overflow, the data in SSPSR is lost. Overflow can only occur in slave mode. The user must read the SSPBUF, even if only transmitting data, to avoid setting overflow. In master operation, the overflow bit is not set since each new reception (and transmission) is initiated by writing to the SSPBUF register. 0 = No overflow In I2C mode 1 = A byte is received while the SSPBUF register is still holding the previous byte. SSPOV is a "don't care" in transmit mode. SSPOV must be cleared in software in either mode. 0 = No overflow
bit 6:
bit 5:
SSPEN: Synchronous Serial Port Enable bit In SPI mode 1 = Enables serial port and configures SCK, SDO, and SDI as serial port pins 0 = Disables serial port and configures these pins as I/O port pins In I2C mode 1 = Enables the serial port and configures the SDA and SCL pins as serial port pins 0 = Disables serial port and configures these pins as I/O port pins In both modes, when enabled, these pins must be properly configured as input or output.
bit 4:
CKP: Clock Polarity Select bit In SPI mode 1 = Idle state for clock is a high level 0 = Idle state for clock is a low level In I2C mode SCK release control 1 = Enable clock 0 = Holds clock low (clock stretch)
bit 3-0: SSPM3:SSPM0: Synchronous Serial Port Mode Select bits 0000 = SPI master operation, clock = FOSC/4 0001 = SPI master operation, clock = FOSC/16 0010 = SPI master operation, clock = FOSC/64 0011 = SPI master operation, clock = TMR2 output/2 0100 = SPI slave mode, clock = SCK pin. SS pin control enabled. 0101 = SPI slave mode, clock = SCK pin. SS pin control disabled. SS can be used as I/O pin 0110 = I2C slave mode, 7-bit address 0111 = I2C slave mode, 10-bit address 1011 = I2C firmware controlled master operation (slave idle) 1110 = I2C slave mode, 7-bit address with start and stop bit interrupts enabled 1111 = I2C slave mode, 10-bit address with start and stop bit interrupts enabled
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 47
PIC16C62B/72A
NOTES:
DS35008B-page 48
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
9.0
Note:
ANALOG-TO-DIGITAL CONVERTER (A/D) MODULE
This section applies to the PIC16C72A only.
Additional information on the A/D module is available in the PICmicroTM Mid-Range Reference Manual, (DS33023). The A/D module has three registers. These registers are: * A/D Result Register (ADRES) * A/D Control Register 0 (ADCON0) * A/D Control Register 1 (ADCON1) A device reset forces all registers to their reset state. This forces the A/D module to be turned off, and any conversion is aborted. The ADCON0 register, shown in Figure 9-1, controls the operation of the A/D module. The ADCON1 register, shown in Figure 9-2, configures the functions of the port pins. The port pins can be configured as analog inputs (RA3 can also be a voltage reference) or as digital I/O.
The analog-to-digital (A/D) converter module has five input channels. The A/D allows conversion of an analog input signal to a corresponding 8-bit digital number (refer to Application Note AN546 for use of A/D Converter). The output of the sample and hold is the input into the converter, which generates the result via successive approximation. The analog reference voltage is software selectable to either the device's positive supply voltage (VDD) or the voltage level on the RA3/AN3/VREF pin. The A/D converter has the feature of being able to operate while the device is in SLEEP mode. To operate in sleep, the A/D conversion clock must be derived from the A/D's internal RC oscillator.
REGISTER 9-1:ADCON0 REGISTER (ADDRESS 1Fh)
R/W-0 R/W-0 ADCS1 ADCS0 bit7 R/W-0 CHS2 R/W-0 CHS1 R/W-0 CHS0 R/W-0 GO/DONE U-0 -- R/W-0 ADON bit0
R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset
bit 7-6: ADCS1:ADCS0: A/D Conversion Clock Select bits 00 = FOSC/2 01 = FOSC/8 10 = FOSC/32 11 = FRC (clock derived from an internal RC oscillator) bit 5-3: CHS2:CHS0: Analog Channel Select bits 000 = channel 0, (RA0/AN0) 001 = channel 1, (RA1/AN1) 010 = channel 2, (RA2/AN2) 011 = channel 3, (RA3/AN3) 100 = channel 4, (RA5/AN4) bit 2: GO/DONE: A/D Conversion Status bit If ADON = 1 1 = A/D conversion in progress (setting this bit starts the A/D conversion) 0 = A/D conversion not in progress (This bit is automatically cleared by hardware when the A/D conversion is complete) bit 1: bit 0: Unimplemented: Read as '0' ADON: A/D On bit 1 = A/D converter module is operating 0 = A/D converter module is shutoff and consumes no operating current
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 49
PIC16C62B/72A
REGISTER 9-2:ADCON1 REGISTER (ADDRESS 9Fh)
U-0 -- bit7 U-0 -- U-0 -- U-0 -- U-0 -- R/W-0 PCFG2 R/W-0 PCFG1 R/W-0 PCFG0 bit0
R = Readable bit W = Writable bit U = Unimplemented bit, read as `0' - n = Value at POR reset
bit 7-3: Unimplemented: Read as '0' bit 2-0: PCFG2:PCFG0: A/D Port Configuration Control bits PCFG2:PCFG0 000 001 010 011 100 101 11x A = Analog input D = Digital I/O RA0 A A A A A A D RA1 A A A A A A D RA2 A A A A D D D RA5 A A A A D D D RA3 A VREF A VREF A VREF D VREF VDD RA3 VDD RA3 VDD RA3 VDD
DS35008B-page 50
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
When the A/D conversion is complete, the result is loaded into the ADRES register, the GO/DONE bit, ADCON0<2>, is cleared, and the A/D interrupt flag bit, ADIF, is set. The block diagram of the A/D module is shown in Figure 9-1. The value that is in the ADRES register is not modified for a Power-on Reset. The ADRES register will contain unknown data after a Power-on Reset. After the A/D module has been configured as desired, the selected channel must be acquired before the conversion is started. The analog input channels must have their corresponding TRIS bits selected as an input. To determine acquisition time, see Section 9.1. After this acquisition time has elapsed, the A/D conversion can be started. The following steps should be followed for doing an A/D conversion: 1. Configure the A/D module: * Configure analog pins / voltage reference / and digital I/O (ADCON1) * Select A/D input channel (ADCON0) * Select A/D conversion clock (ADCON0) * Turn on A/D module (ADCON0) Configure A/D interrupt (if desired): * Clear ADIF bit * Set ADIE bit * Set GIE bit Wait the required acquisition time. Start conversion: * Set GO/DONE bit (ADCON0) Wait for A/D conversion to complete, by either: * Polling for the GO/DONE bit to be cleared OR 6. 7. * Waiting for the A/D interrupt Read A/D Result register (ADRES), clear bit ADIF if required. For next conversion, go to step 1 or step 2 as required. The A/D conversion time per bit is defined as TAD. A minimum wait of 2TAD is required before next acquisition starts.
2.
3. 4. 5.
FIGURE 9-1:
A/D BLOCK DIAGRAM
CHS2:CHS0
100 VIN (Input voltage) 011 010 A/D Converter 001 RA1/AN1 VDD VREF (Reference voltage) PCFG2:PCFG0 000 010 100 11x 001 011 101 or or or or or 000 RA0/AN0 RA2/AN2 RA5/AN4 RA3/AN3/VREF
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 51
PIC16C62B/72A
9.1 A/D Acquisition Requirements
For the A/D converter to meet its specified accuracy, the charge holding capacitor (CHOLD) must be allowed to fully charge to the input channel voltage level. The analog input model is shown in Figure 9-2. The source impedance (RS) and the internal sampling switch (RSS) impedance directly affect the time required to charge the capacitor CHOLD. The sampling switch (RSS) impedance varies over the device voltage (VDD). The source impedance affects the offset voltage at the analog input (due to pin leakage current). The maximum recommended impedance for analog sources is 10 k. After the analog input channel is selected (changed), this acquisition must pass before the conversion can be started. To calculate the minimum acquisition time, TACQ, see Equation 9-1. This equation calculates the acquisition time to within 1/2 LSb error (512 steps for the A/D). The 1/2 LSb error is the maximum error allowed for the A/D to meet its specified accuracy. Note: When the conversion is started, the holding capacitor is disconnected from the input pin.
In general; Assuming RS Vdd = 10k = 3.0V (RSS = 10k)
Temp. = 50C (122F) TACQ 13.0 Sec By increasing VDD and reducing RS and Temp., TACQ can be substantially reduced.
FIGURE 9-2:
ANALOG INPUT MODEL
VDD VT = 0.6V RIC 1k Sampling Switch SS RSS CHOLD = DAC capacitance = 51.2 pF VSS Legend CPIN = input capacitance VT = threshold voltage I leakage = leakage current at the pin due to various junctions RIC SS CHOLD = interconnect resistance = sampling switch = sample/hold capacitance (from DAC)
Rs
ANx
VA
CPIN 5 pF
VT = 0.6V
I leakage 500 nA
6V 5V VDD 4V 3V 2V
5 6 7 8 9 10 11 RSS (k)
EQUATION 9-1:
TACQ =
ACQUISITION TIME
Amplifier Settling Time + Hold Capacitor Charging Time + Temperature Coefficient TAMP + TC + TCOFF TAMP = 5S TC = - (51.2pF)(1k + RSS + RS) In(1/511) TCOFF = (Temp -25C)(0.05S/C)
=
DS35008B-page 52
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
9.2 Selecting the A/D Conversion Clock 9.3 Configuring Analog Port Pins
The A/D conversion time per bit is defined as TAD. The A/D conversion requires 9.5TAD per 8-bit conversion. The source of the A/D conversion clock is software selectable. The four possible options for TAD are: * * * * 2TOSC 8TOSC 32TOSC Internal RC oscillator The ADCON1 and TRISA registers control the operation of the A/D port pins. The port pins that are desired as analog inputs must have their corresponding TRIS bits set (input). If the TRIS bit is cleared (output), the digital output level (VOH or VOL) will be converted. The A/D operation is independent of the state of the CHS2:CHS0 bits and the TRIS bits. Note 1: When reading the port register, all pins configured as analog input channels will read as cleared (a low level). Pins configured as digital inputs, will convert an analog input. Analog levels on a digitally configured input will not affect the conversion accuracy. Note 2: Analog levels on any pin that is defined as a digital input (including the AN4:AN0 pins) may cause the input buffer to consume current that is out of the devices specification.
For correct A/D conversions, the A/D conversion clock (TAD) must be selected to ensure a minimum TAD time of 1.6 s. The A/D module can operate during sleep mode, but the RC oscillator must be selected as the A/D clock source prior to the SLEEP instruction. Table 9-1 shows the resultant TAD times derived from the device operating frequencies and the A/D clock source selected.
TABLE 9-1
TAD vs. DEVICE OPERATING FREQUENCIES
Device Frequency 20 MHz 100 ns(2) 400 ns(2) 1.6 s 5 MHz 400 1.6 s 6.4 s ns(2) 1.25 MHz 1.6 s 6.4 s 25.6 s(3) 333.33 kHz 6 s 24 s(3) 96 s(3)
AD Clock Source (TAD) Operation 2TOSC 8TOSC 32TOSC RC(5) Legend: Note 1: 2: 3: 4: ADCS1:ADCS0 00 01 10 11
2 - 6 s(1,4) 2 - 6 s(1,4) 2 - 6 s(1) 2 - 6 s(1,4) Shaded cells are outside of recommended range. The RC source has a typical TAD time of 4 s. These values violate the minimum required TAD time. For faster conversion times, the selection of another clock source is recommended. When device frequency is greater than 1 MHz, the RC A/D conversion clock source is recommended for sleep operation only. 5: For extended voltage devices (LC), please refer to Electrical Specifications section.
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 53
PIC16C62B/72A
9.4
Note:
A/D Conversions
The GO/DONE bit should NOT be set in the same instruction that turns on the A/D.
9.5
Use of the CCP Trigger
An A/D conversion can be started by the "special event trigger" of the CCP1 module. This requires that the CCP1M3:CCP1M0 bits (CCP1CON<3:0>) be programmed as 1011 and that the A/D module be enabled (ADON bit is set). When the trigger occurs, the
GO/DONE bit will be set, starting the A/D conversion, and the Timer1 counter will be reset to zero. Timer1 is reset to automatically repeat the A/D acquisition period with minimal software overhead. The appropriate analog input channel must be selected and the minimum acquisition time must pass before the "special event trigger" sets the GO/DONE bit (starts a conversion). If the A/D module is not enabled (ADON is cleared), then the "special event trigger" will be ignored by the A/D module, but will still reset the Timer1 counter.
TABLE 9-2
Address Name 0Bh,8Bh 0Ch 8Ch 1Eh 1Fh 9Fh 05h 85h
SUMMARY OF A/D REGISTERS
Bit 7 GIE -- -- Bit 6 PEIE ADIF ADIE Bit 5 T0IE -- -- Bit 4 INTE -- -- Bit 3 RBIE SSPIF SSPIE Bit 2 T0IF CCP1IF CCP1IE Bit 1 INTF Bit 0 RBIF Value on POR, BOR 0000 000x Value on all other Resets 0000 000u -0-- 0000 -0-- 0000 uuuu uuuu 0000 00-0 ---- -000 --0u 0000 --11 1111
INTCON PIR1 PIE1 ADRES
TMR2IF TMR1IF -0-- 0000 TMR2IE TMR1IE -0-- 0000 xxxx xxxx
A/D Result Register CHS2 -- RA5 CHS1 -- RA4 CHS0 -- RA3 GO/DONE PCFG2 RA2 -- PCFG1 RA1 ADON PCFG0 RA0
ADCON0 ADCS1 ADCS0 ADCON1 PORTA TRISA -- -- -- -- -- --
0000 00-0 ---- -000 --0x 0000 --11 1111
PORTA Data Direction Register
Legend: x = unknown, u = unchanged, - = unimplemented read as '0'. Shaded cells are not used for A/D conversion.
DS35008B-page 54
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
10.0 SPECIAL FEATURES OF THE CPU
other is the Power-up Timer (PWRT), which provides a fixed delay on power-up only and is designed to keep the part in reset while the power supply stabilizes. With these two timers on-chip, most applications need no external reset circuitry. SLEEP mode is designed to offer a very low current power-down mode. The user can wake-up from SLEEP through external reset, Watchdog Timer Wake-up, or through an interrupt. Several oscillator options are also made available to allow the part to fit the application. The RC oscillator option saves system cost while the LP crystal option saves power. A set of configuration bits are used to select various options. Additional information on special features is available in the PICmicroTM Mid-Range Reference Manual, (DS33023).
The PIC16C62B/72A devices have a host of features intended to maximize system reliability, minimize cost through elimination of external components, provide power saving operating modes and offer code protection. These are: * Oscillator Mode Selection * Reset - Power-on Reset (POR) - Power-up Timer (PWRT) - Oscillator Start-up Timer (OST) - Brown-out Reset (BOR) * Interrupts * Watchdog Timer (WDT) * SLEEP * Code protection * ID locations * In-circuit serial programmingTM (ICSP) These devices have a Watchdog Timer, which can be shut off only through configuration bits. It runs off its own RC oscillator for added reliability. There are two timers that offer necessary delays on power-up. One is the Oscillator Start-up Timer (OST), intended to keep the chip in reset until the crystal oscillator is stable. The
10.1
Configuration Bits
The configuration bits can be programmed (read as '0') or left unprogrammed (read as '1') to select various device configurations. These bits are mapped in program memory location 2007h. The user will note that address 2007h is beyond the user program memory space. In fact, it belongs to the special test/configuration memory space (2000h 3FFFh), which can be accessed only during programming.
FIGURE 10-1: CONFIGURATION WORD
CP1 bit13 CP0 CP1 CP0 CP1 CP0 -- BODEN CP1 CP0 PWRTE WDTE FOSC1 FOSC0 bit0
Register: Address:
CONFIG 2007h
bit 13-8 5-4:
CP1:CP0: Code Protection bits (2) 11 = Code protection off 10 = Upper half of program memory code protected 01 = Upper 3/4th of program memory code protected 00 = All memory is code protected Unimplemented: Read as '1' BODEN: Brown-out Reset Enable bit (1) 1 = BOR enabled 0 = BOR disabled PWRTE: Power-up Timer Enable bit (1) 1 = PWRT disabled 0 = PWRT enabled WDTE: Watchdog Timer Enable bit 1 = WDT enabled 0 = WDT disabled FOSC1:FOSC0: Oscillator Selection bits 11 = RC oscillator 10 = HS oscillator 01 = XT oscillator 00 = LP oscillator
bit 7: bit 6:
bit 3:
bit 2:
bit 1-0:
Note 1: Enabling Brown-out Reset automatically enables Power-up Timer (PWRT), regardless of the value of bit PWRTE. All of the CP1:CP0 pairs must be given the same value to enable the code protection scheme listed.
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 55
PIC16C62B/72A
10.2
10.2.1
Oscillator Configurations
OSCILLATOR TYPES
TABLE 10-1
Ranges Tested: Mode XT
CERAMIC RESONATORS
The PIC16CXXX can be operated in four different oscillator modes. The user can program two configuration bits (FOSC1 and FOSC0) to select one of these four modes: * * * * LP XT HS RC Low Power Crystal Crystal/Resonator High Speed Crystal/Resonator Resistor/Capacitor CRYSTAL OSCILLATOR/CERAMIC RESONATORS
Freq 455 kHz 2.0 MHz 4.0 MHz 8.0 MHz 16.0 MHz
OSC1 68 - 100 pF 15 - 68 pF 15 - 68 pF 10 - 68 pF 10 - 22 pF
OSC2 68 - 100 pF 15 - 68 pF 15 - 68 pF 10 - 68 pF 10 - 22 pF
HS
These values are for design guidance only. See notes at bottom of page.
10.2.2
Resonators Used: 455 kHz 2.0 MHz 4.0 MHz 8.0 MHz 16.0 MHz Panasonic EFO-A455K04B Murata Erie CSA2.00MG Murata Erie CSA4.00MG Murata Erie CSA8.00MT Murata Erie CSA16.00MX 0.3% 0.5% 0.5% 0.5% 0.5%
In XT, LP or HS modes, a crystal or ceramic resonator is connected to the OSC1/CLKIN and OSC2/CLKOUT pins to establish oscillation (Figure 10-2). The PIC16CXXX oscillator design requires the use of a parallel cut crystal. Use of a series cut crystal may give a frequency out of the crystal manufacturers specifications. When in XT, LP or HS modes, the device can use an external clock source to drive the OSC1/CLKIN pin (Figure 10-3).
Resonators did not have built-in capacitors.
TABLE 10-2
CAPACITOR SELECTION FOR CRYSTAL OSCILLATOR
Crystal Freq 32 kHz 200 kHz 200 kHz 1 MHz 4 MHz Cap. Range C1 33 pF 15 pF 47-68 pF 15 pF 15 pF 15 pF 15-33 pF 15-33 pF Cap. Range C2 33 pF 15 pF 47-68 pF 15 pF 15 pF 15 pF 15-33 pF 15-33 pF
Osc Type LP XT
FIGURE 10-2: CRYSTAL/CERAMIC RESONATOR OPERATION (HS, XT OR LP OSC CONFIGURATION)
C1(1) OSC1 To internal logic SLEEP PIC16CXXX
HS
4 MHz 8 MHz 20 MHz
XTAL OSC2 RS(2) C2(1)
RF(3)
These values are for design guidance only. See notes at bottom of page. Crystals Used 32 kHz 200 kHz 1 MHz 4 MHz 8 MHz 20 MHz Epson C-001R32.768K-A STD XTL 200.000KHz ECS ECS-10-13-1 ECS ECS-40-20-1 EPSON CA-301 8.000M-C EPSON CA-301 20.000M-C 20 PPM 20 PPM 50 PPM 50 PPM 30 PPM 30 PPM
Note1: See Table 10-1 and Table 10-2 for recommended values of C1 and C2. 2: A series resistor (RS) may be required for AT strip cut crystals. 3: RF varies with the crystal chosen.
FIGURE 10-3: EXTERNAL CLOCK INPUT OPERATION (HS, XT OR LP OSC CONFIGURATION)
Clock from ext. system Open OSC1 PIC16CXXX OSC2
Note 1:
Higher capacitance increases the stability of the oscillator, but also increases the start-up time. 2: Since each resonator/crystal has its own characteristics, the user should consult the resonator/crystal manufacturer for appropriate values of external components. 3: Rs may be required in HS mode, as well as XT mode, to avoid overdriving crystals with low drive level specification. 4: Oscillator performance should be verified when migrating between devices (including PIC16C62A to PIC16C62B and PIC16C72 to PIC16C72A)
DS35008B-page 56
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
10.2.3 RC OSCILLATOR
10.3
Reset
For timing insensitive applications, the "RC" device option offers additional cost savings. The RC oscillator frequency is a function of the supply voltage, the resistor (REXT) and capacitor (CEXT) values, and the operating temperature. In addition to this, the oscillator frequency will vary from unit to unit due to normal process parameter variation. Furthermore, the difference in lead frame capacitance between package types will also affect the oscillation frequency, especially for low CEXT values. The user also needs to take into account variation due to tolerance of external R and C components used. Figure 10-4 shows how the R/C combination is connected to the PIC16CXXX.
The PIC16CXXX differentiates between various kinds of reset: * * * * * * Power-on Reset (POR) MCLR reset during normal operation MCLR reset during SLEEP WDT Reset (during normal operation) WDT Wake-up (during SLEEP) Brown-out Reset (BOR)
FIGURE 10-4: RC OSCILLATOR MODE
VDD Rext OSC1 Cext VSS Fosc/4 Recommended values: OSC2/CLKOUT 3 k Rext 100 k Cext > 20pF Internal clock PIC16CXX
Some registers are not affected in any reset condition; their status is unknown on POR and unchanged by any other reset. Most other registers are reset to a "reset state" on Power-on Reset (POR), on the MCLR and WDT Reset, on MCLR reset during SLEEP, and on Brown-out Reset (BOR). They are not affected by a WDT Wake-up from SLEEP, which is viewed as the resumption of normal operation. The TO and PD bits are set or cleared depending on the reset situation, as indicated in Table 10-4. These bits are used in software to determine the nature of the reset. See Table 10-6 for a full description of reset states of all registers. A simplified block diagram of the on-chip reset circuit is shown in Figure 10-5. The PICmicro devices have a MCLR noise filter in the MCLR reset path. The filter will ignore small pulses. However, a valid MCLR pulse must meet the minimum pulse width (TmcL, Specification #30). No internal reset source (WDT, BOR, POR) willdrive the MCLR pin low.
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 57
PIC16C62B/72A
FIGURE 10-5: SIMPLIFIED BLOCK DIAGRAM OF ON-CHIP RESET CIRCUIT
External Reset MCLR WDT Module VDD rise detect VDD Brown-out Reset OST/PWRT OST 10-bit Ripple counter OSC1 (1) On-chip RC OSC PWRT 10-bit Ripple counter R Q Chip_Reset Power-on Reset S SLEEP WDT Time-out Reset
BODEN
Enable PWRT Enable OST Note 1: This is a separate oscillator from the RC oscillator of the CLKIN pin.
DS35008B-page 58
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
10.4 Power-On Reset (POR) 10.5 Power-up Timer (PWRT)
A Power-on Reset pulse is generated on-chip when VDD rise is detected (in the range of 1.5V - 2.1V). To take advantage of the POR, just tie the MCLR pin directly (or through a resistor) to VDD. This will eliminate external RC components usually needed to create a Power-on Reset. A maximum rise time for VDD is specified (SVDD, parameter D004). For a slow rise time, see Figure 10-6. When the device starts normal operation (exits the reset condition), device operating parameters (voltage, frequency, temperature,...) must be met to ensure operation. If these conditions are not met, the device must be held in reset until the operating conditions are met. Brown-out Reset may be used to meet the start-up conditions. The Power-up Timer provides a fixed nominal time-out (TPWRT, parameter #33) from the POR. The Power-up Timer operates on an internal RC oscillator. The chip is kept in reset as long as the PWRT is active. The PWRT's time delay allows VDD to rise to an acceptable level. A configuration bit is provided to enable/disable the PWRT. The power-up time delay will vary from chip-to-chip due to VDD, temperature and process variation. See DC parameters for details.
10.6
Oscillator Start-up Timer (OST)
FIGURE 10-6: EXTERNAL POWER-ON RESET CIRCUIT (FOR SLOW VDD POWER-UP)
VDD D R R1 MCLR C PIC16CXX
The Oscillator Start-up Timer (OST) provides a delay of 1024 oscillator cycles (from OSC1 input) after the PWRT delay is over (TOST, parameter #32). This ensures that the crystal oscillator or resonator has started and stabilized. The OST time-out is invoked only for XT, LP and HS modes and only on Power-on Reset or wake-up from SLEEP. Note: The OST delay may not occur when the device wakes from SLEEP.
10.7
Brown-Out Reset (BOR)
Note 1: External Power-on Reset circuit is required only if VDD power-up slope is too slow. The diode D helps discharge the capacitor quickly when VDD powers down. 2: R < 40 k is recommended to make sure that voltage drop across R does not violate the device's electrical specification. 3: R1 = 100 to 1 k will limit any current flowing into MCLR from external capacitor C in the event of MCLR/VPP pin breakdown due to Electrostatic Discharge (ESD) or Electrical Overstress (EOS).
The configuration bit, BODEN, can enable or disable the Brown-Out Reset circuit. If VPP falls below Vbor (parameter #35, about 100S), the brown-out situation will reset the device. If VDD falls below VBOR for less than TBOR, a reset may not occur. Once the brown-out occurs, the device will remain in brown-out reset until VDD rises above VBOR. The power-up timer then keeps the device in reset for TPWRT (parameter #33, about 72mS). If VDD should fall below VBOR during TPWRT, the brown-out reset process will restart when VDD rises above VBOR with the power-up timer reset. The power-up timer is always enabled when the brown-out reset circuit is enabled, regardless of the state of the PWRT configuration bit.
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 59
PIC16C62B/72A
10.8 Time-out Sequence
When a POR reset occurs, the PWRT delay starts (if enabled). When PWRT ends, the OST counts 1024 oscillator cycles (LP, XT, HS modes only). When OST completes, the device comes out of reset. The total time-out will vary based on oscillator configuration and the status of the PWRT. For example, in RC mode with the PWRT disabled, there will be no time-out at all. If MCLR is kept low long enough, the time-outs will expire. Bringing MCLR high will begin execution immediately. This is useful for testing purposes or to synchronize more than one PIC16CXXX device operating in parallel. Table 10-5 shows the reset conditions for the STATUS, PCON and PC registers, while Table 10-6 shows the reset conditions for all the registers.
10.9
Power Control/Status Register (PCON)
The BOR bit is unknown on Power-on Reset. If the Brown-out Reset circuit is used, the BOR bit must be set by the user and checked on subsequent resets to see if it was cleared, indicating a Brown-out has occurred. POR (Power-on Reset Status bit) is cleared on a Power-on Reset and unaffected otherwise. The user
Status Register
IRP RP1 RP0 TO PD Z DC C
PCON Register
POR BOR
TABLE 10-3
TIME-OUT IN VARIOUS SITUATIONS
Power-up PWRTE = 0 72 ms + 1024TOSC 72 ms PWRTE = 1 1024TOSC -- Brown-out 72 ms + 1024TOSC 72 ms Wake-up from SLEEP 1024TOSC --
Oscillator Configuration XT, HS, LP RC
TABLE 10-4
POR 0 0 0 1 1 1 1 1 BOR x x x 0 1 1 1 1
STATUS BITS AND THEIR SIGNIFICANCE
TO 1 0 x 1 0 0 u 1 PD 1 x 0 1 1 0 u 0 Power-on Reset Illegal, TO is set on POR Illegal, PD is set on POR Brown-out Reset WDT Reset WDT Wake-up MCLR Reset during normal operation MCLR Reset during SLEEP or interrupt wake-up from SLEEP
TABLE 10-5
RESET CONDITION FOR SPECIAL REGISTERS
Condition Program Counter 000h 000h 000h 000h PC + 1 000h PC + 1(1) STATUS Register 0001 1xxx 000u uuuu 0001 0uuu 0000 1uuu uuu0 0uuu 0001 1uuu uuu1 0uuu PCON Register ---- --0x ---- --uu ---- --uu ---- --uu ---- --uu ---- --u0 ---- --uu
Power-on Reset MCLR Reset during normal operation MCLR Reset during SLEEP WDT Reset WDT Wake-up Brown-out Reset Interrupt wake-up from SLEEP
Note 1:
Legend: u = unchanged, x = unknown, - = unimplemented bit read as '0'.
When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector (0004h).
DS35008B-page 60
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
TABLE 10-6
Register W INDF TMR0 PCL STATUS FSR PORTA(4) PORTB(5) PORTC(5) PCLATH INTCON PIR1 TMR1L TMR1H T1CON TMR2 T2CON SSPBUF SSPCON CCPR1L CCPR1H CCP1CON ADRES ADCON0 OPTION_REG TRISA TRISB TRISC PIE1 PCON PR2 SSPADD SSPSTAT ADCON1
Legend: Note 1: 2: 3: 4: 5:
INITIALIZATION CONDITIONS FOR ALL REGISTERS
Applicable Devices 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 62B 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A 72A Power-on Reset, Brown-out Reset xxxx xxxx N/A xxxx xxxx 0000h 0001 1xxx xxxx xxxx --0x 0000 xxxx xxxx xxxx xxxx ---0 0000 0000 000x ---- 0000 -0-- 0000 xxxx xxxx xxxx xxxx --00 0000 0000 0000 -000 0000 xxxx xxxx 0000 0000 xxxx xxxx xxxx xxxx --00 0000 xxxx xxxx 0000 00-0 1111 1111 --11 1111 1111 1111 1111 1111 ---- 0000 -0-- 0000 ---- --0q 1111 1111 0000 0000 0000 0000 ---- -000 MCLR Resets WDT Reset uuuu uuuu N/A uuuu uuuu 0000h 000q quuu(3) uuuu uuuu --0u 0000 uuuu uuuu uuuu uuuu ---0 0000 0000 000u ---- 0000 -0-- 0000 uuuu uuuu uuuu uuuu --uu uuuu 0000 0000 -000 0000 uuuu uuuu 0000 0000 uuuu uuuu uuuu uuuu --00 0000 uuuu uuuu 0000 00-0 1111 1111 --11 1111 1111 1111 1111 1111 ---- 0000 -0-- 0000 ---- --uq 1111 1111 0000 0000 0000 0000 ---- -000 Wake-up via WDT or Interrupt uuuu uuuu N/A uuuu uuuu PC + 1(2) uuuq quuu(3) uuuu uuuu --uu uuuu uuuu uuuu uuuu uuuu ---u uuuu uuuu uuuu(1) ---- uuuu(1) -u-- uuuu(1) uuuu uuuu uuuu uuuu --uu uuuu uuuu uuuu -uuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu uuuu --uu uuuu uuuu uuuu uuuu uu-u uuuu uuuu --uu uuuu uuuu uuuu uuuu uuuu ---- uuuu -u-- uuuu ---- --uq 1111 1111 uuuu uuuu uuuu uuuu ---- -uuu
u = unchanged, x = unknown, - = unimplemented bit, read as '0', q = value depends on condition One or more bits in INTCON and/or PIR1 will be affected (to cause wake-up). When the wake-up is due to an interrupt and the GIE bit is set, the PC is loaded with the interrupt vector (0004h). See Table 10-5 for reset value for specific condition. On any device reset, these pins are configured as inputs. This is the value that will be in the port output latch.
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 61
PIC16C62B/72A
10.10 Interrupts
The interrupt control register (INTCON) records individual interrupt requests in flag bits. It also has individual and global interrupt enable bits. Note: Individual interrupt flag bits are set regardless of the status of their corresponding mask bit or the GIE bit. The peripheral interrupt flags are contained in the special function registers PIR1 and PIR2. The corresponding interrupt enable bits are contained in special function registers PIE1 and PIE2, and the peripheral interrupt enable bit is contained in special function register INTCON. When an interrupt is responded to, the GIE bit is cleared to disable any further interrupts, the return address is pushed onto the stack and the PC is loaded with 0004h. Once in the interrupt service routine, the source of the interrupt can be determined by polling the interrupt flag bits. The interrupt flag bit must be cleared in software before re-enabling interrupts to avoid recursive interrupts. For external interrupt events, such as the INT pin or PORTB change interrupt, the interrupt latency will be three or four instruction cycles, depending on when the interrupt event occurs. The latency is the same for one or two cycle instructions. Individual interrupt flag bits are set regardless of the status of their corresponding mask bit or the GIE bit
A global interrupt enable bit, GIE (INTCON<7>) enables or disables all interrupts. When bit GIE is enabled, and an interrupt's flag bit and mask bit are set, the interrupt will vector immediately. Individual interrupts can be disabled through their corresponding enable bits in various registers. Individual interrupt flag bits are set regardless of the status of the GIE bit. The GIE bit is cleared on reset. The "return from interrupt" instruction, RETFIE, exits the interrupt routine and sets the GIE bit, which reenables interrupts. The RB0/INT pin interrupt, the RB port change interrupt and the TMR0 overflow interrupt flags are contained in the INTCON register.
FIGURE 10-7: INTERRUPT LOGIC
Wake-up (If in SLEEP mode)
T0IF T0IE INTF INTE ADIF(1) ADIE(1) SSPIF SSPIE CCP1IF CCP1IE TMR2IF TMR2IE TMR1IF TMR1IE RBIF RBIE PEIE GIE
Interrupt to CPU
Note 1: The A/D module is not implemented on the PIC16C62B.
DS35008B-page 62
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
10.10.1 INT INTERRUPT The external interrupt on RB0/INT pin is edge triggered: either rising, if bit INTEDG (OPTION_REG<6>) is set, or falling, if the INTEDG bit is clear. When a valid edge appears on the RB0/INT pin, flag bit INTF (INTCON<1>) is set. This interrupt can be disabled by clearing enable bit INTE (INTCON<4>). Flag bit INTF must be cleared in software in the interrupt service routine before re-enabling this interrupt. The INT interrupt can wake-up the processor from SLEEP, if bit INTE was set prior to going into SLEEP. The status of global interrupt enable bit GIE decides whether or not the processor branches to the interrupt vector following wake-up. See Section 10.13 for details on SLEEP mode. 10.10.2 TMR0 INTERRUPT An overflow (FFh 00h) in the TMR0 register will set flag bit T0IF (INTCON<2>). The interrupt can be enabled/disabled by setting/clearing enable bit T0IE (INTCON<5>). (Section 4.0) 10.10.3 PORTB INTCON CHANGE An input change on PORTB<7:4> sets flag bit RBIF (INTCON<0>). The interrupt can be enabled/disabled by setting/clearing enable bit RBIE (INTCON<4>). (Section 3.2)
10.11
Context Saving During Interrupts
During an interrupt, only the return PC value is saved on the stack. Typically, users may wish to save key registers during an interrupt, (i.e., W register and STATUS register). This will have to be implemented in software. Example 10-1 stores and restores the W and STATUS registers. The register, W_TEMP, must be defined in each bank and must be defined at the same offset from the bank base address (i.e., if W_TEMP is defined at 0x20 in bank 0, it must also be defined at 0xA0 in bank 1). The example: a) b) c) d) e) f) Stores the W register. Stores the STATUS register in bank 0. Stores the PCLATH register. Executes the interrupt service routine code (User-generated). Restores the STATUS register (and bank select bit). Restores the W and PCLATH registers.
EXAMPLE 10-1: SAVING STATUS, W, AND PCLATH REGISTERS IN RAM
MOVWF SWAPF CLRF MOVWF : :(ISR) : SWAPF MOVWF SWAPF SWAPF W_TEMP STATUS,W STATUS STATUS_TEMP ;Copy ;Swap ;bank ;Save W to TEMP register, could be bank one or zero status to be saved into W 0, regardless of current bank, Clears IRP,RP1,RP0 status to bank zero STATUS_TEMP register
STATUS_TEMP,W STATUS W_TEMP,F W_TEMP,W
;Swap STATUS_TEMP register into W ;(sets bank to original state) ;Move W into STATUS register ;Swap W_TEMP ;Swap W_TEMP into W
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 63
PIC16C62B/72A
10.12 Watchdog Timer (WDT)
The Watchdog Timer is a free running on-chip RC oscillator which does not require any external components. This RC oscillator is separate from the RC oscillator of the OSC1/CLKIN pin. The WDT will run, even if the clock on the OSC1/CLKIN and OSC2/CLKOUT pins of the device has been stopped, for example, by execution of a SLEEP instruction. During normal operation, a WDT time-out generates a device RESET (Watchdog Timer Reset). If the device is in SLEEP mode, a WDT time-out causes the device to wake-up and continue with normal operation (Watchdog Timer Wake-up). The TO bit in the STATUS register will be cleared upon a Watchdog Timer time-out. The WDT can be permanently disabled by clearing configuration bit WDTE (Section 10.1). The WDT time-out period (TWDT, parameter #31) is multiplied by the prescaler ratio, when the prescaler is assigned to the WDT. The prescaler assignment (assigned to either the WDT or Timer0) and prescaler ratio are set in the OPTION_REG register. Note: The CLRWDT and SLEEP instructions clear the WDT and the postscaler, if assigned to the WDT, and prevent it from timing out and generating a device RESET condition.
. Note: When a CLRWDT instruction is executed and the prescaler is assigned to the WDT, the prescaler count will be cleared, but the prescaler assignment is not changed.
FIGURE 10-8: WATCHDOG TIMER BLOCK DIAGRAM
From TMR0 Clock Source (Figure 4-2) 0 WDT Timer 1 M U X Postscaler 8 8 - to - 1 MUX WDT Enable Bit PSA To TMR0 (Figure 4-2) 0 MUX 1 PSA PS2:PS0
Note: PSA and PS2:PS0 are bits in the OPTION_REG register.
WDT Time-out
FIGURE 10-9: SUMMARY OF WATCHDOG TIMER REGISTERS
Address 2007h 81h Name Config. bits
OPTION_REG
Bit 7
Bit 6 BODEN
Bit 5 CP1 T0CS
Bit 4 CP0 T0SE
Bit 3 PWRTE PSA
Bit 2 WDTE PS2
Bit 1 FOSC1 PS1
Bit 0 FOSC0 PS0
RBPU
INTEDG
Legend: Shaded cells are not used by the Watchdog Timer.
DS35008B-page 64
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
10.13 Power-down Mode (SLEEP)
Power-down mode is entered by executing a SLEEP instruction. If enabled, the Watchdog Timer will be cleared but keeps running, the PD bit (STATUS<3>) is cleared, the TO (STATUS<4>) bit is set, and the oscillator driver is turned off. The I/O ports maintain the status they had, before the SLEEP instruction was executed (driving high, low or hi-impedance). For lowest current consumption in this mode, place all I/O pins at either VDD or VSS, ensure no external circuitry is drawing current from the I/O pin, power-down the A/D and disable external clocks. Pull all I/O pins that are hi-impedance inputs, high or low externally, to avoid switching currents caused by floating inputs. The T0CKI input should also be at VDD or VSS for lowest current consumption. The contribution from on-chip pull-ups on PORTB should be considered. The MCLR pin must be at a logic high level (VIHMC, parameter D042). 10.13.1 WAKE-UP FROM SLEEP The device can wake up from SLEEP through one of the following events: 1. 2. 3. External reset input on MCLR pin. Watchdog Timer Wake-up (if WDT was enabled). Interrupt from INT pin, RB port change, or some Peripheral Interrupts. regardless of the state of the GIE bit. If the GIE bit is clear (disabled), the device resumes execution at the instruction after the SLEEP instruction. If the GIE bit is set (enabled), the device executes the instruction after the SLEEP instruction and then branches to the interrupt address (0004h). In cases where the execution of the instruction following SLEEP is not desirable, a NOP should follow the SLEEP instruction. 10.13.2 WAKE-UP USING INTERRUPTS When global interrupts are disabled (GIE cleared) and any interrupt source has both its interrupt enable bit and interrupt flag bit set, one of the following will occur: * If the interrupt occurs before the execution of a SLEEP instruction, the SLEEP instruction will complete as a NOP. Therefore, the WDT and WDT postscaler will not be cleared, the TO bit will not be set and PD bits will not be cleared. * If the interrupt occurs during or after the execution of a SLEEP instruction, the device will immediately wake up from sleep. The SLEEP instruction will be completely executed before the wake-up. Therefore, the WDT and WDT postscaler will be cleared, the TO bit will be set and the PD bit will be cleared. Even if the flag bits were checked before executing a SLEEP instruction, it may be possible for flag bits to become set before the SLEEP instruction completes. To determine whether a SLEEP instruction executed, test the PD bit. If the PD bit is set, the SLEEP instruction was executed as a NOP. To ensure that the WDT is cleared, a CLRWDT instruction should be executed before a SLEEP instruction.
External MCLR Reset will cause a device reset. All other events are considered a continuation of program execution and cause a "wake-up". The TO and PD bits in the STATUS register can be used to determine the cause of device reset. The PD bit, which is set on power-up, is cleared when SLEEP is invoked. The TO bit is cleared if a WDT time-out occurred (and caused wake-up). The following peripheral interrupts can wake the device from SLEEP: 1. 2. 3. TMR1 interrupt. Timer1 must be operating as an asynchronous counter. CCP capture mode interrupt. Special event trigger (Timer1 in asynchronous mode using an external clock. CCP1 is in compare mode). SSP (Start/Stop) bit detect interrupt. SSP transmit or receive in slave mode (SPI/I2C). USART RX or TX (synchronous slave mode).
4. 5. 6.
Other peripherals cannot generate interrupts since during SLEEP, no on-chip clocks are present. When the SLEEP instruction is being executed, the next instruction (PC + 1) is pre-fetched. For the device to wake-up through an interrupt event, the corresponding interrupt enable bit must be set (enabled). Wake-up is
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 65
PIC16C62B/72A
FIGURE 10-10: WAKE-UP FROM SLEEP THROUGH INTERRUPT
Q1 Q2 Q3 Q4 OSC1 CLKOUT(4) INT pin INTF flag (INTCON<1>) GIE bit (INTCON<7>) INSTRUCTION FLOW PC Instruction fetched Instruction executed PC Inst(PC) = SLEEP Inst(PC - 1) PC+1 Inst(PC + 1) SLEEP PC+2 PC+2 Inst(PC + 2) Inst(PC + 1) Dummy cycle PC + 2 0004h Inst(0004h) Dummy cycle 0005h Inst(0005h) Inst(0004h) Processor in SLEEP Interrupt Latency (Note 2) TOST(2) Q1 Q2 Q3 Q4 Q1 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4 Q1 Q2 Q3 Q4
Note 1: 2: 3: 4:
XT, HS or LP oscillator mode assumed. TOST = 1024TOSC (drawing not to scale) This delay will not be there for RC osc mode. GIE = '1' assumed. In this case after wake- up, the processor jumps to the interrupt routine. If GIE = '0', execution will continue in-line. CLKOUT is not available in these osc modes, but shown here for timing reference.
10.14
Program Verification/Code Protection
If the code protection bits have not been programmed, the on-chip program memory can be read out for verification purposes. Note: Microchip does not recommend code protecting windowed devices.
10.15
ID Locations
Four memory locations (2000h - 2003h) are designated as ID locations where the user can store checksum or other code-identification numbers. These locations are not accessible during normal execution, but are readable and writable during program/verify. It is recommended that only the 4 least significant bits of the ID location are used. For ROM devices, these values are submitted along with the ROM code.
10.16
In-Circuit Serial ProgrammingTM
PIC16CXXX microcontrollers can be serially programmed while in the end application circuit. This is simply done with two lines for clock and data, and three more lines for power, ground and the programming voltage. This allows customers to manufacture boards with unprogrammed devices, and then program the microcontroller just before shipping the product. This also allows the most recent firmware or a custom firmware to be programmed. For complete details of serial programming, please refer to the In-Circuit Serial Programming (ICSPTM) Guide, DS30277.
DS35008B-page 66
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
11.0 INSTRUCTION SET SUMMARY
Each PIC16CXXX instruction is a 14-bit word divided into an OPCODE which specifies the instruction type and one or more operands which further specify the operation of the instruction. The PIC16CXX instruction set summary in Table 11-2 lists byte-oriented, bit-oriented, and literal and control operations. Table 11-1 shows the opcode field descriptions. For byte-oriented instructions, 'f' represents a file register designator and 'd' represents a destination designator. The file register designator specifies which file register is to be used by the instruction. The destination designator specifies where the result of the operation is to be placed. If 'd' is zero, the result is placed in the W register. If 'd' is one, the result is placed in the file register specified in the instruction. For bit-oriented instructions, 'b' represents a bit field designator which selects the number of the bit affected by the operation, while 'f' represents the number of the file in which the bit is located. For literal and control operations, 'k' represents an eight or eleven bit constant or literal value. execution time is 1 s. If a conditional test is true or the program counter is changed as a result of an instruction, the instruction execution time is 2 s. Table 11-2 lists the instructions recognized by the MPASM assembler. Figure 11-1 shows the general formats that the instructions can have. Note: To maintain upward compatibility with future PIC16CXXX products, do not use the OPTION and TRIS instructions.
All examples use the following format to represent a hexadecimal number: 0xhh where h signifies a hexadecimal digit.
FIGURE 11-1: GENERAL FORMAT FOR INSTRUCTIONS
Byte-oriented file register operations 13 876 OPCODE d f (FILE #) d = 0 for destination W d = 1 for destination f f = 7-bit file register address Bit-oriented file register operations 13 10 9 76 OPCODE b (BIT #) f (FILE #) b = 3-bit bit address f = 7-bit file register address Literal and control operations General 13 OPCODE k = 8-bit immediate value CALL and GOTO instructions only 13 11 OPCODE 10 k (literal) 0 8 7 k (literal) 0 0
TABLE 11-1
Field
f W b k x
OPCODE FIELD DESCRIPTIONS
Description
0
Register file address (0x00 to 0x7F) Working register (accumulator) Bit address within an 8-bit file register Literal field, constant data or label Don't care location (= 0 or 1) The assembler will generate code with x = 0. It is the recommended form of use for compatibility with all Microchip software tools. Destination select; d = 0: store result in W, d = 1: store result in file register f. Default is d = 1 Program Counter Time-out bit Power-down bit Zero bit Digit Carry bit Carry bit
d
PC TO PD Z DC C
k = 11-bit immediate value
The instruction set is highly orthogonal and is grouped into three basic categories: * Byte-oriented operations * Bit-oriented operations * Literal and control operations All instructions are executed within one single instruction cycle, unless a conditional test is true or the program counter is changed as a result of an instruction. In this case, the execution takes two instruction cycles with the second cycle executed as a NOP. One instruction cycle consists of four oscillator periods. Thus, for an oscillator frequency of 4 MHz, the normal instruction
A description of each instruction is available in the PICmicroTM Mid-Range Reference Manual, (DS33023).
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 67
PIC16C62B/72A
TABLE 11-2
Mnemonic, Operands
PIC16CXXX INSTRUCTION SET
Description Cycles MSb 14-Bit Opcode LSb Status Affected Notes
BYTE-ORIENTED FILE REGISTER OPERATIONS ADDWF ANDWF CLRF CLRW COMF DECF DECFSZ INCF INCFSZ IORWF MOVF MOVWF NOP RLF RRF SUBWF SWAPF XORWF f, d f, d f f, d f, d f, d f, d f, d f, d f, d f f, d f, d f, d f, d f, d Add W and f AND W with f Clear f Clear W Complement f Decrement f Decrement f, Skip if 0 Increment f Increment f, Skip if 0 Inclusive OR W with f Move f Move W to f No Operation Rotate Left f through Carry Rotate Right f through Carry Subtract W from f Swap nibbles in f Exclusive OR W with f 1 1 1 1 1 1 1(2) 1 1(2) 1 1 1 1 1 1 1 1 1 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 0111 0101 0001 0001 1001 0011 1011 1010 1111 0100 1000 0000 0000 1101 1100 0010 1110 0110 dfff dfff lfff 0000 dfff dfff dfff dfff dfff dfff dfff lfff 0xx0 dfff dfff dfff dfff dfff ffff ffff ffff 0011 ffff ffff ffff ffff ffff ffff ffff ffff 0000 ffff ffff ffff ffff ffff C,DC,Z Z Z Z Z Z Z Z Z 1,2 1,2 2 1,2 1,2 1,2,3 1,2 1,2,3 1,2 1,2
C C C,DC,Z Z
1,2 1,2 1,2 1,2 1,2
BIT-ORIENTED FILE REGISTER OPERATIONS BCF BSF BTFSC BTFSS f, b f, b f, b f, b Bit Clear f Bit Set f Bit Test f, Skip if Clear Bit Test f, Skip if Set 1 1 1 (2) 1 (2) 01 01 01 01 00bb 01bb 10bb 11bb bfff bfff bfff bfff ffff ffff ffff ffff 1,2 1,2 3 3
LITERAL AND CONTROL OPERATIONS ADDLW ANDLW CALL CLRWDT GOTO IORLW MOVLW RETFIE RETLW RETURN SLEEP SUBLW XORLW Note 1: k k k k k k k k k Add literal and W AND literal with W Call subroutine Clear Watchdog Timer Go to address Inclusive OR literal with W Move literal to W Return from interrupt Return with literal in W Return from Subroutine Go into standby mode Subtract W from literal Exclusive OR literal with W 1 1 2 1 2 1 1 2 2 2 1 1 1 11 11 10 00 10 11 11 00 11 00 00 11 11 111x 1001 0kkk 0000 1kkk 1000 00xx 0000 01xx 0000 0000 110x 1010 kkkk kkkk kkkk 0110 kkkk kkkk kkkk 0000 kkkk 0000 0110 kkkk kkkk kkkk kkkk kkkk 0100 kkkk kkkk kkkk 1001 kkkk 1000 0011 kkkk kkkk C,DC,Z Z TO,PD Z
TO,PD C,DC,Z Z
When an I/O register is modified as a function of itself ( e.g., MOVF PORTB, 1), the value used will be that value present on the pins themselves. For example, if the data latch is '1' for a pin configured as input and is driven low by an external device, the data will be written back with a '0'. 2: If this instruction is executed on the TMR0 register (and, where applicable, d = 1), the prescaler will be cleared if assigned to the Timer0 Module. 3: If Program Counter (PC) is modified or a conditional test is true, the instruction requires two cycles. The second cycle is executed as a NOP.
DS35008B-page 68
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
11.1
ADDLW Syntax: Operands: Operation: Status Affected: Description:
Instruction Descriptions
Add Literal and W [label] ADDLW 0 k 255 (W) + k (W) C, DC, Z
The contents of the W register are added to the eight bit literal 'k' and the result is placed in the W register.
ANDWF Syntax: Operands: Operation: Status Affected: Description:
AND W with f [label] ANDWF 0 f 127 d [0,1] (W) .AND. (f) (destination) Z
AND the W register with register 'f'. If 'd' is 0, the result is stored in the W register. If 'd' is 1, the result is stored back in register 'f'.
k
f,d
ADDWF Syntax: Operands: Operation: Status Affected: Description:
Add W and f [label] ADDWF 0 f 127 d [0,1] (W) + (f) (destination) C, DC, Z
Add the contents of the W register with register 'f'. If 'd' is 0, the result is stored in the W register. If 'd' is 1, the result is stored back in register 'f'.
BCF f,d Syntax: Operands: Operation: Status Affected: Description:
Bit Clear f [label] BCF 0 f 127 0b7 0 (f) None
Bit 'b' in register 'f' is cleared.
f,b
ANDLW Syntax: Operands: Operation: Status Affected: Description:
AND Literal with W [label] ANDLW 0 k 255 (W) .AND. (k) (W) Z
The contents of W register are AND'ed with the eight bit literal 'k'. The result is placed in the W register.
BSF Syntax: Operands: Operation: Status Affected: Description:
Bit Set f [label] BSF 0 f 127 0b7 1 (f) None
Bit 'b' in register 'f' is set.
k
f,b
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 69
PIC16C62B/72A
BTFSS Syntax: Operands: Operation: Status Affected: Description: Bit Test f, Skip if Set [label] BTFSS f,b 0 f 127 0b<7 skip if (f) = 1 None
If bit 'b' in register 'f' is '0', then the next instruction is executed. If bit 'b' is '1', then the next instruction is discarded and a NOP is executed instead, making this a 2TCY instruction.
CLRF Syntax: Operands: Operation: Status Affected: Description:
Clear f [label] CLRF 0 f 127 00h (f) 1Z Z
The contents of register 'f' are cleared and the Z bit is set.
f
BTFSC Syntax: Operands: Operation: Status Affected: Description:
Bit Test, Skip if Clear [label] BTFSC f,b 0 f 127 0b7 skip if (f) = 0 None
If bit 'b' in register 'f' is '1', then the next instruction is executed. If bit 'b' in register 'f' is '0', then the next instruction is discarded, and a NOP is executed instead, making this a 2TCY instruction.
CLRW Syntax: Operands: Operation: Status Affected: Description:
Clear W [ label ] CLRW None 00h (W) 1Z Z
W register is cleared. Zero bit (Z) is set.
CALL Syntax: Operands: Operation:
Call Subroutine [ label ] CALL k 0 k 2047 (PC)+ 1 TOS, k PC<10:0>, (PCLATH<4:3>) PC<12:11> None
Call Subroutine. First, return address (PC+1) is pushed onto the stack. The eleven bit immediate address is loaded into PC bits <10:0>. The upper bits of the PC are loaded from PCLATH. CALL is a two cycle instruction.
CLRWDT Syntax: Operands: Operation:
Clear Watchdog Timer [ label ] CLRWDT None 00h WDT 0 WDT prescaler, 1 TO 1 PD TO, PD
CLRWDT instruction resets the Watchdog Timer. It also resets the prescaler of the WDT. Status bits TO and PD are set.
Status Affected: Description:
Status Affected: Description:
DS35008B-page 70
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
COMF Syntax: Operands: Operation: Status Affected: Description: Complement f [ label ] COMF 0 f 127 d [0,1] (f) (destination) Z
The contents of register 'f' are complemented. If 'd' is 0, the result is stored in W. If 'd' is 1, the result is stored back in register 'f'.
GOTO f,d Syntax: Operands: Operation: Status Affected: Description:
Unconditional Branch [ label ] GOTO k 0 k 2047 k PC<10:0> PCLATH<4:3> PC<12:11> None
GOTO is an unconditional branch. The eleven bit immediate value is loaded into PC bits <10:0>. The upper bits of PC are loaded from PCLATH<4:3>. GOTO is a two cycle instruction.
DECF Syntax: Operands: Operation: Status Affected: Description:
Decrement f [label] DECF f,d 0 f 127 d [0,1] (f) - 1 (destination) Z
Decrement register 'f'. If 'd' is 0, the result is stored in the W register. If 'd' is 1, the result is stored back in register 'f'.
INCF Syntax: Operands: Operation: Status Affected: Description:
Increment f [ label ] INCF f,d 0 f 127 d [0,1] (f) + 1 (destination) Z
The contents of register 'f' are incremented. If 'd' is 0, the result is placed in the W register. If 'd' is 1, the result is placed back in register 'f'.
DECFSZ Syntax: Operands: Operation: Status Affected: Description:
Decrement f, Skip if 0 [ label ] DECFSZ f,d 0 f 127 d [0,1] (f) - 1 (destination); skip if result = 0 None
The contents of register 'f' are decremented. If 'd' is 0, the result is placed in the W register. If 'd' is 1, the result is placed back in register 'f'. If the result is 1, the next instruction, is executed. If the result is 0, then a NOP is executed instead making it a 2TCY instruction.
INCFSZ Syntax: Operands: Operation: Status Affected: Description:
Increment f, Skip if 0 [ label ] INCFSZ f,d 0 f 127 d [0,1] (f) + 1 (destination), skip if result = 0 None
The contents of register 'f' are incremented. If 'd' is 0, the result is placed in the W register. If 'd' is 1, the result is placed back in register 'f'. If the result is 1, the next instruction is executed. If the result is 0, a NOP is executed instead making it a 2TCY instruction.
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 71
PIC16C62B/72A
IORLW Syntax: Operands: Operation: Status Affected: Description: Inclusive OR Literal with W [ label ] IORLW k 0 k 255 (W) .OR. k (W) Z
The contents of the W register is OR'ed with the eight bit literal 'k'. The result is placed in the W register.
MOVLW Syntax: Operands: Operation: Status Affected: Description:
Move Literal to W [ label ] k (W) None
The eight bit literal 'k' is loaded into W register. The don't cares will assemble as 0's.
MOVLW k
0 k 255
IORWF Syntax: Operands: Operation: Status Affected: Description:
Inclusive OR W with f [ label ] IORWF f,d 0 f 127 d [0,1] (W) .OR. (f) (destination) Z
Inclusive OR the W register with register 'f'. If 'd' is 0, the result is placed in the W register. If 'd' is 1, the result is placed back in register 'f'.
MOVWF Syntax: Operands: Operation: Status Affected: Description:
Move W to f [ label ] (W) (f) None
Move data from W register to register 'f'.
MOVWF
f
0 f 127
MOVF Syntax: Operands: Operation: Status Affected: Description:
Move f [ label ] MOVF f,d 0 f 127 d [0,1] (f) (destination) Z
The contents of register f is moved to a destination dependant upon the status of d. If d = 0, destination is W register. If d = 1, the destination is file register f itself. d = 1 is useful to test a file register since status flag Z is affected.
NOP Syntax: Operands: Operation: Status Affected: Description:
No Operation [ label ] None No operation None
No operation.
NOP
DS35008B-page 72
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
RETFIE Syntax: Operands: Operation: Status Affected: Return from Interrupt [ label ] None TOS PC, 1 GIE None RETFIE RLF Syntax: Operands: Operation: Status Affected: Description: Rotate Left f through Carry [ label ] RLF f,d 0 f 127 d [0,1] See description below C
The contents of register 'f' are rotated one bit to the left through the Carry Flag. If 'd' is 0, the result is placed in the W register. If 'd' is 1, the result is stored back in register 'f'. C Register f
RETLW Syntax: Operands: Operation: Status Affected: Description:
Return with Literal in W [ label ] RETLW k 0 k 255 k (W); TOS PC None
The W register is loaded with the eight bit literal 'k'. The program counter is loaded from the top of the stack (the return address). This is a two cycle instruction.
RRF Syntax: Operands: Operation: Status Affected: Description:
Rotate Right f through Carry [ label ] RRF f,d 0 f 127 d [0,1] See description below C
The contents of register 'f' are rotated one bit to the right through the Carry Flag. If 'd' is 0, the result is placed in the W register. If 'd' is 1, the result is placed back in register 'f'. C Register f
RETURN Syntax: Operands: Operation: Status Affected: Description:
Return from Subroutine [ label ] None TOS PC None
Return from subroutine. The stack is POPed and the top of the stack (TOS) is loaded into the program counter. This is a two cycle instruction.
SLEEP Syntax: Operands: Operation: [ label ] None 00h WDT, 0 WDT prescaler, 1 TO, 0 PD TO, PD
The power-down status bit, PD is cleared. Time-out status bit, TO is set. Watchdog Timer and its prescaler are cleared. The processor is put into SLEEP mode with the oscillator stopped. See Section 10.13 for more details.
RETURN
SLEEP
Status Affected: Description:
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 73
PIC16C62B/72A
SUBLW Syntax: Operands: Operation: Description: Subtract W from Literal [ label ] SUBLW k 0 k 255 k - (W) (W)
The W register is subtracted (2's complement method) from the eight bit literal 'k'. The result is placed in the W register.
XORLW Syntax: Operands: Operation: Status Affected: Description:
Exclusive OR Literal with W [label] XORLW k 0 k 255 (W) .XOR. k (W) Z
The contents of the W register are XOR'ed with the eight bit literal 'k'. The result is placed in the W register.
Status Affected: C, DC, Z
SUBWF Syntax: Operands: Operation: Status Affected: Description:
Subtract W from f [ label ] 0 f 127 d [0,1] (f) - (W) (destination) C, DC, Z
Subtract (2's complement method) W register from register 'f'. If 'd' is 0, the result is stored in the W register. If 'd' is 1, the result is stored back in register 'f'.
XORWF Syntax: Operands: Operation: Status Affected: Description:
Exclusive OR W with f [label] XORWF f,d 0 f 127 d [0,1] (W) .XOR. (f) (destination) Z
Exclusive OR the contents of the W register with register 'f'. If 'd' is 0, the result is stored in the W register. If 'd' is 1, the result is stored back in register 'f'.
SUBWF f,d
SWAPF Syntax: Operands: Operation: Status Affected: Description:
Swap Nibbles in f [ label ] SWAPF f,d 0 f 127 d [0,1] (f<3:0>) (destination<7:4>), (f<7:4>) (destination<3:0>) None
The upper and lower nibbles of register 'f' are exchanged. If 'd' is 0, the result is placed in W register. If 'd' is 1, the result is placed in register 'f'.
DS35008B-page 74
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
12.0 DEVELOPMENT SUPPORT
(R)
MPLAB allows you to: * Edit your source files (either assembly or `C') * One touch assemble (or compile) and download to PICmicro tools (automatically updates all project information) * Debug using: - source files - absolute listing file - object code The ability to use MPLAB with Microchip's simulator, MPLAB-SIM, allows a consistent platform and the ability to easily switch from the cost-effective simulator to the full featured emulator with minimal retraining.
The PICmicro microcontrollers are supported with a full range of hardware and software development tools: * Integrated Development Environment - MPLABTM IDE Software * Assemblers/Compilers/Linkers - MPASM Assembler - MPLAB-C17 and MPLAB-C18 C Compilers - MPLINK/MPLIB Linker/Librarian * Simulators - MPLAB-SIM Software Simulator * Emulators - MPLAB-ICE Real-Time In-Circuit Emulator - PICMASTER(R)/PICMASTER-CE In-Circuit Emulator - ICEPICTM * In-Circuit Debugger - MPLAB-ICD for PIC16F877 * Device Programmers - PRO MATE(R) II Universal Programmer - PICSTART(R) Plus Entry-Level Prototype Programmer * Low-Cost Demonstration Boards - SIMICE - PICDEM-1 - PICDEM-2 - PICDEM-3 - PICDEM-17 - SEEVAL(R) - KEELOQ(R)
12.2
MPASM Assembler
MPASM is a full featured universal macro assembler for all PICmicro MCU's. It can produce absolute code directly in the form of HEX files for device programmers, or it can generate relocatable objects for MPLINK. MPASM has a command line interface and a Windows shell and can be used as a standalone application on a Windows 3.x or greater system. MPASM generates relocatable object files, Intel standard HEX files, MAP files to detail memory usage and symbol reference, an absolute LST file which contains source lines and generated machine code, and a COD file for MPLAB debugging. MPASM features include: * MPASM and MPLINK are integrated into MPLAB projects. * MPASM allows user defined macros to be created for streamlined assembly. * MPASM allows conditional assembly for multi purpose source files. * MPASM directives allow complete control over the assembly process.
12.1
MPLAB Integrated Development Environment Software
*
* * * * *
- The MPLAB IDE software brings an ease of software development previously unseen in the 8-bit microcontroller market. MPLAB is a Windows(R)-based application which contains: Multiple functionality - editor - simulator - programmer (sold separately) - emulator (sold separately) A full featured editor A project manager Customizable tool bar and key mapping A status bar On-line help
12.3
MPLAB-C17 and MPLAB-C18 C Compilers
The MPLAB-C17 and MPLAB-C18 Code Development Systems are complete ANSI `C' compilers and integrated development environments for Microchip's PIC17CXXX and PIC18CXXX family of microcontrollers, respectively. These compilers provide powerful integration capabilities and ease of use not found with other compilers. For easier source level debugging, the compilers provide symbol information that is compatible with the MPLAB IDE memory display.
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 75
PIC16C62B/72A
12.4 MPLINK/MPLIB Linker/Librarian
MPLINK is a relocatable linker for MPASM and MPLAB-C17 and MPLAB-C18. It can link relocatable objects from assembly or C source files along with precompiled libraries using directives from a linker script. MPLIB is a librarian for pre-compiled code to be used with MPLINK. When a routine from a library is called from another source file, only the modules that contains that routine will be linked in with the application. This allows large libraries to be used efficiently in many different applications. MPLIB manages the creation and modification of library files. MPLINK features include: * MPLINK works with MPASM and MPLAB-C17 and MPLAB-C18. * MPLINK allows all memory areas to be defined as sections to provide link-time flexibility. MPLIB features include: * MPLIB makes linking easier because single libraries can be included instead of many smaller files. * MPLIB helps keep code maintainable by grouping related modules together. * MPLIB commands allow libraries to be created and modules to be added, listed, replaced, deleted, or extracted. Interchangeable processor modules allow the system to be easily reconfigured for emulation of different processors. The universal architecture of the MPLAB-ICE allows expansion to support new PICmicro microcontrollers. The MPLAB-ICE Emulator System has been designed as a real-time emulation system with advanced features that are generally found on more expensive development tools. The PC platform and Microsoft(R) Windows 3.x/95/98 environment were chosen to best make these features available to you, the end user. MPLAB-ICE 2000 is a full-featured emulator system with enhanced trace, trigger, and data monitoring features. Both systems use the same processor modules and will operate across the full operating speed range of the PICmicro MCU.
12.7
PICMASTER/PICMASTER CE
The PICMASTER system from Microchip Technology is a full-featured, professional quality emulator system. This flexible in-circuit emulator provides a high-quality, universal platform for emulating Microchip 8-bit PICmicro microcontrollers (MCUs). PICMASTER systems are sold worldwide, with a CE compliant model available for European Union (EU) countries.
12.8
ICEPIC
12.5
MPLAB-SIM Software Simulator
The MPLAB-SIM Software Simulator allows code development in a PC host environment by simulating the PICmicro series microcontrollers on an instruction level. On any given instruction, the data areas can be examined or modified and stimuli can be applied from a file or user-defined key press to any of the pins. The execution can be performed in single step, execute until break, or trace mode. MPLAB-SIM fully supports symbolic debugging using MPLAB-C17 and MPLAB-C18 and MPASM. The Software Simulator offers the flexibility to develop and debug code outside of the laboratory environment making it an excellent multi-project software development tool.
ICEPIC is a low-cost in-circuit emulation solution for the Microchip Technology PIC16C5X, PIC16C6X, PIC16C7X, and PIC16CXXX families of 8-bit one-timeprogrammable (OTP) microcontrollers. The modular system can support different subsets of PIC16C5X or PIC16CXXX products through the use of interchangeable personality modules or daughter boards. The emulator is capable of emulating without target application circuitry being present.
12.9
MPLAB-ICD In-Circuit Debugger
12.6
MPLAB-ICE High Performance Universal In-Circuit Emulator with MPLAB IDE
The MPLAB-ICE Universal In-Circuit Emulator is intended to provide the product development engineer with a complete microcontroller design tool set for PICmicro microcontrollers (MCUs). Software control of MPLAB-ICE is provided by the MPLAB Integrated Development Environment (IDE), which allows editing, "make" and download, and source debugging from a single environment.
Microchip's In-Circuit Debugger, MPLAB-ICD, is a powerful, low-cost run-time development tool. This tool is based on the flash PIC16F877 and can be used to develop for this and other PICmicro microcontrollers from the PIC16CXXX family. MPLAB-ICD utilizes the In-Circuit Debugging capability built into the PIC16F87X. This feature, along with Microchip's In-Circuit Serial Programming protocol, offers cost-effective in-circuit flash programming and debugging from the graphical user interface of the MPLAB Integrated Development Environment. This enables a designer to develop and debug source code by watching variables, single-stepping and setting break points. Running at full speed enables testing hardware in real-time. The MPLAB-ICD is also a programmer for the flash PIC16F87X family.
DS35008B-page 76
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
12.10 PRO MATE II Universal Programmer
The PRO MATE II Universal Programmer is a full-featured programmer capable of operating in stand-alone mode as well as PC-hosted mode. PRO MATE II is CE compliant. The PRO MATE II has programmable VDD and VPP supplies which allows it to verify programmed memory at VDD min and VDD max for maximum reliability. It has an LCD display for instructions and error messages, keys to enter commands and a modular detachable socket assembly to support various package types. In stand-alone mode the PRO MATE II can read, verify or program PICmicro devices. It can also set code-protect bits in this mode. the PICDEM-1 board, on a PRO MATE II or PICSTART-Plus programmer, and easily test firmware. The user can also connect the PICDEM-1 board to the MPLAB-ICE emulator and download the firmware to the emulator for testing. Additional prototype area is available for the user to build some additional hardware and connect it to the microcontroller socket(s). Some of the features include an RS-232 interface, a potentiometer for simulated analog input, push-button switches and eight LEDs connected to PORTB.
12.14
PICDEM-2 Low-Cost PIC16CXX Demonstration Board
12.11
PICSTART Plus Entry Level Development System
The PICSTART programmer is an easy-to-use, lowcost prototype programmer. It connects to the PC via one of the COM (RS-232) ports. MPLAB Integrated Development Environment software makes using the programmer simple and efficient. PICSTART Plus supports all PICmicro devices with up to 40 pins. Larger pin count devices such as the PIC16C92X, and PIC17C76X may be supported with an adapter socket. PICSTART Plus is CE compliant.
12.12
SIMICE Entry-Level Hardware Simulator
The PICDEM-2 is a simple demonstration board that supports the PIC16C62, PIC16C64, PIC16C65, PIC16C73 and PIC16C74 microcontrollers. All the necessary hardware and software is included to run the basic demonstration programs. The user can program the sample microcontrollers provided with the PICDEM-2 board, on a PRO MATE II programmer or PICSTART-Plus, and easily test firmware. The MPLAB-ICE emulator may also be used with the PICDEM-2 board to test firmware. Additional prototype area has been provided to the user for adding additional hardware and connecting it to the microcontroller socket(s). Some of the features include a RS-232 interface, push-button switches, a potentiometer for simulated analog input, a Serial EEPROM to demonstrate usage of the I2C bus and separate headers for connection to an LCD module and a keypad.
SIMICE is an entry-level hardware development system designed to operate in a PC-based environment with Microchip's simulator MPLAB-SIM. Both SIMICE and MPLAB-SIM run under Microchip Technology's MPLAB Integrated Development Environment (IDE) software. Specifically, SIMICE provides hardware simulation for Microchip's PIC12C5XX, PIC12CE5XX, and PIC16C5X families of PICmicro 8-bit microcontrollers. SIMICE works in conjunction with MPLAB-SIM to provide non-real-time I/O port emulation. SIMICE enables a developer to run simulator code for driving the target system. In addition, the target system can provide input to the simulator code. This capability allows for simple and interactive debugging without having to manually generate MPLAB-SIM stimulus files. SIMICE is a valuable debugging tool for entry-level system development.
12.15
PICDEM-3 Low-Cost PIC16CXXX Demonstration Board
12.13
PICDEM-1 Low-Cost PICmicro Demonstration Board
The PICDEM-1 is a simple board which demonstrates the capabilities of several of Microchip's microcontrollers. The microcontrollers supported are: PIC16C5X (PIC16C54 to PIC16C58A), PIC16C61, PIC16C62X, PIC16C71, PIC16C8X, PIC17C42, PIC17C43 and PIC17C44. All necessary hardware and software is included to run basic demo programs. The users can program the sample microcontrollers provided with
The PICDEM-3 is a simple demonstration board that supports the PIC16C923 and PIC16C924 in the PLCC package. It will also support future 44-pin PLCC microcontrollers with a LCD Module. All the necessary hardware and software is included to run the basic demonstration programs. The user can program the sample microcontrollers provided with the PICDEM-3 board, on a PRO MATE II programmer or PICSTART Plus with an adapter socket, and easily test firmware. The MPLAB-ICE emulator may also be used with the PICDEM-3 board to test firmware. Additional prototype area has been provided to the user for adding hardware and connecting it to the microcontroller socket(s). Some of the features include an RS-232 interface, push-button switches, a potentiometer for simulated analog input, a thermistor and separate headers for connection to an external LCD module and a keypad. Also provided on the PICDEM-3 board is an LCD panel, with 4 commons and 12 segments, that is capable of displaying time, temperature and day of the week. The PICDEM-3 provides an additional RS-232 interface and Windows 3.1 software for showing the demultiplexed LCD signals on a PC. A simple serial interface allows the user to construct a hardware demultiplexer for the LCD signals.
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 77
PIC16C62B/72A
12.16 PICDEM-17
The PICDEM-17 is an evaluation board that demonstrates the capabilities of several Microchip microcontrollers, including PIC17C752, PIC17C756, PIC17C762, and PIC17C766. All necessary hardware is included to run basic demo programs, which are supplied on a 3.5-inch disk. A programmed sample is included, and the user may erase it and program it with the other sample programs using the PRO MATE II or PICSTART Plus device programmers and easily debug and test the sample code. In addition, PICDEM-17 supports down-loading of programs to and executing out of external FLASH memory on board. The PICDEM-17 is also usable with the MPLAB-ICE or PICMASTER emulator, and all of the sample programs can be run and modified using either emulator. Additionally, a generous prototype area is available for user hardware.
12.17
SEEVAL Evaluation and Programming System
The SEEVAL SEEPROM Designer's Kit supports all Microchip 2-wire and 3-wire Serial EEPROMs. The kit includes everything necessary to read, write, erase or program special features of any Microchip SEEPROM product including Smart SerialsTM and secure serials. The Total EnduranceTM Disk is included to aid in tradeoff analysis and reliability calculations. The total kit can significantly reduce time-to-market and result in an optimized system.
12.18
KEELOQ Evaluation and Programming Tools
KEELOQ evaluation and programming tools support Microchips HCS Secure Data Products. The HCS evaluation kit includes an LCD display to show changing codes, a decoder to decode transmissions, and a programming interface to program test transmitters.
DS35008B-page 78
Preliminary
(c) 1999 Microchip Technology Inc.
24CXX/ 25CXX/ 93CXX
PIC14000
HCSXXX
PIC16C5X
PIC16C6X
PIC16C7X
PIC16C8X
PIC17C4X
PIC16F62X
PIC16C7XX
PIC16F8XX
PIC16C9XX
PIC17C7XX
PIC12CXXX
PIC16CXXX
PIC18CXX2
MCRFXXX
MCP2510
TABLE 12-1:
MPLABTM Integrated Development Environment
a
a
a
a
a
a
a
a
a
a
a
a
aa
aa
MPLABTM C17 Compiler
Software Tools
MPLABTM C18 Compiler
Emulators
Programmers Debugger
Demo Boards and Eval Kits
(c) 1999 Microchip Technology Inc.
MPASM/MPLINK
a
a
aaa
aa
aa
MPLABTM-ICE
**
aaa
aaa
aaa
PICMASTER/PICMASTER-CE
aaa a
aaa a
aaa a
aaa a
aaa a
aaa a
aaa a
aaa a
ICEPICTM Low-Cost In-Circuit Emulator
MPLAB-ICD In-Circuit Debugger
*
*
a
**
a
a
PICSTART(R)Plus Low-Cost Universal Dev. Kit
a
**
a
a
a
a
a
a
a
a
a
a
a
a
a
PRO MATE(R) II Universal Programmer
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
a
SIMICE
a
DEVELOPMENT TOOLS FROM MICROCHIP
Preliminary
aa a a

PICDEM-1
a
aa
PICDEM-2
a
a
PICDEM-3
a
PICDEM-14A
a
PICDEM-17
a
KEELOQ(R) Evaluation Kit
aa
KEELOQ Transponder Kit
microIDTM Programmer's Kit
125 kHz microID Developer's Kit
aa a
125 kHz Anticollision microID Developer's Kit
13.56 MHz Anticollision microID Developer's Kit
a
MCP2510 CAN Developer's Kit
a
PIC16C62B/72A
DS35008B-page 79
* Contact the Microchip Technology Inc. web site at www.microchip.com for information on how to use the MPLAB-ICD In-Circuit Debugger (DV164001) with PIC16C62, 63, 64, 65, 72, 73, 74, 76, 77 ** Contact Microchip Technology Inc. for availability date. Development tool is available on select devices.
PIC16C62B/72A
NOTES:
DS35008B-page 80
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
13.0 ELECTRICAL CHARACTERISTICS
Absolute Maximum Ratings () Ambient temperature under bias.............................................................................................................-55C to +125C Storage temperature .............................................................................................................................. -65C to +150C Voltage on any pin with respect to VSS (except VDD, MCLR, and RA4).......................................... -0.3V to (VDD + 0.3V) Voltage on VDD with respect to VSS ......................................................................................................... -0.3V to +7.5V Voltage on MCLR with respect to VSS (Note 2).......................................................................................... 0V to +13.25V Voltage on RA4 with respect to Vss ............................................................................................................... 0V to +8.5V Total power dissipation (Note 1)................................................................................................................................1.0W Maximum current out of VSS pin ...........................................................................................................................300 mA Maximum current into VDD pin ..............................................................................................................................250 mA Input clamp current, IIK (VI < 0 or VI > VDD)...................................................................................................................... 20 mA Output clamp current, IOK (VO < 0 or VO > VDD) .............................................................................................................. 20 mA Maximum output current sunk by any I/O pin..........................................................................................................25 mA Maximum output current sourced by any I/O pin ....................................................................................................25 mA Maximum current sunk by PORTA and PORTB (combined) .................................................................................200 mA Maximum current sourced by PORTA and PORTB (combined)............................................................................200 mA Maximum current sunk by PORTC........................................................................................................................200 mA Maximum current sourced by PORTC ..................................................................................................................200 mA Note 1: Power dissipation is calculated as follows: Pdis = VDD x {IDD - IOH} + {(VDD-VOH) x IOH} + (VOl x IOL) 2: Voltage spikes below VSS at the MCLR/VPP pin, inducing currents greater than 80 mA, may cause latch-up. Thus, a series resistor of 50-100 should be used when applying a "low" level to the MCLR/VPP pin, rather than pulling this pin directly to VSS. NOTICE: Stresses above those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at those or any other conditions above those indicated in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability.
(c) 1998 Microchip Technology Inc.
Preliminary
DS35008B-page 81
PIC16C62B/72A
FIGURE 13-1: PIC16C62B/72A-20 VOLTAGE-FREQUENCY GRAPH 6.0 V 5.5 V 5.0 V PIC16CXXX PIC16CXXX-20
Voltage
4.5 V 4.0 V 3.5 V 3.0 V 2.5 V 2.0 V
20 MHz
Frequency
FIGURE 13-2: PIC16LC62B/72A AND PIC16C62B/72A/JW VOLTAGE-FREQUENCY GRAPH 6.0 V 5.5 V 5.0 V
Voltage
4.5 V 4.0 V 3.5 V 3.0 V 2.5 V 2.0 V PIC16LCXXX-04
4 MHz
10 MHz
Frequency
FMAX = (12.0 MHz/V) (VDDAPPMIN - 2.5 V) + 4 MHz Note: VDDAPPMIN is the minimum voltage of the PICmicro(R) device in the application. Fmax is no greater than 10 MHz.
DS35008B-page 82
Preliminary
(c) 1998 Microchip Technology Inc.
PIC16C62B/72A
FIGURE 13-3: PIC16C62B/72A-04 VOLTAGE-FREQUENCY GRAPH 6.0 V 5.5 V 5.0 V PIC16CXXX-04
Voltage
4.5 V 4.0 V 3.5 V 3.0 V 2.5 V 2.0 V
4 MHz
Frequency
(c) 1998 Microchip Technology Inc.
Preliminary
DS35008B-page 83
PIC16C62B/72A
13.1 DC Characteristics: PIC16C62B/72A-04 (Commercial, Industrial, Extended) PIC16C62B/72A-20 (Commercial, Industrial, Extended)
Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial -40C TA +85C for industrial -40C TA +125C for extended Min 4.0 4.5 VBOR* Typ 1.5 VSS Max Units 5.5 5.5 5.5 V V V V V See section on Power-on Reset for details Conditions XT, RC and LP osc mode HS osc mode BOR enabled (Note 7)
DC CHARACTERISTICS Param No. D001 D001A D002* D003 Sym VDD Characteristic Supply Voltage
VDR VPOR
RAM Data Retention Voltage (Note 1) VDD Start Voltage to ensure internal Power-on Reset signal VDD Rise Rate to ensure internal Power-on Reset signal Brown-out Reset voltage trip point Supply Current (Note 2, 5)
D004* SVDD D004A* D005 D010 VBOR IDD
0.05 TBD 3.65 -
2.7
4.35 5
V/ms PWRT enabled (PWRTE bit clear) PWRT disabled (PWRTE bit set) See section on Power-on Reset for details V mA BODEN bit set XT, RC osc modes FOSC = 4 MHz, VDD = 5.5V (Note 4) HS osc mode FOSC = 20 MHz, VDD = 5.5V VDD = 4.0V, WDT enabled,-40C to +85C VDD = 4.0V, WDT disabled, 0C to +70C VDD = 4.0V, WDT disabled,-40C to +85C VDD = 4.0V, WDT disabled,-40C to +125C
D013 D020 D021 D021B Module Differential Current (Note 6) D022* IWDT Watchdog Timer D022A* IBOR Brown-out Reset IPD Power-down Current (Note 3, 5)
-
10 10.5 1.5 1.5 2.5
20 42 16 19 19
mA A A A A
-
6.0 TBD
20 200
A A
WDTE BIT SET, VDD = 4.0V BODEN bit set, VDD = 5.0V
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: This is the limit to which VDD can be lowered without losing RAM data. 2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD, MCLR = VDD; WDT enabled/disabled as specified. 3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS. 4: For RC osc mode, current through Rext is not included. The current through the resistor can be estimated by the formula Ir = VDD/2Rext (mA) with Rext in kOhm. 5: Timer1 oscillator (when enabled) adds approximately 20 A to the specification. This value is from characterization and is for design guidance only. This is not tested. 6: The current is the additional current consumed when this peripheral is enabled. This current should be added to the base IDD or IPD measurement. 7: This is the voltage where the device enters the Brown-out Reset. When BOR is enabled, the device will perform a brown-out reset when VDD falls below VBOR.
DS35008B-page 84
Preliminary
(c) 1998 Microchip Technology Inc.
PIC16C62B/72A
13.2 DC Characteristics: PIC16LC62B/72A-04 (Commercial, Industrial)
Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial -40C TA +85C for industrial Min 2.5 VBOR* Typ 1.5 VSS Max Units 5.5 5.5 V V V V See section on Power-on Reset for details Conditions LP, XT, RC osc modes (DC - 4 MHz) BOR enabled (Note 7)
DC CHARACTERISTICS Param No. D001 D002* D003 Sym VDD VDR VPOR Characteristic Supply Voltage RAM Data Retention Voltage (Note 1) VDD Start Voltage to ensure internal Power-on Reset signal VDD Rise Rate to ensure internal Power-on Reset signal Brown-out Reset voltage trip point Supply Current (Note 2, 5)
D004* SVDD D004A* D005 D010 VBOR IDD
0.05 TBD 3.65 -
2.0
4.35 3.8
V/ms PWRT enabled (PWRTE bit clear) PWRT disabled (PWRTE bit set) See section on Power-on Reset for details V mA A A A A BODEN bit set XT, RC osc modes FOSC = 4 MHz, VDD = 3.0V (Note 4) LP OSC MODE FOSC = 32 kHz, VDD = 3.0V, WDT disabled VDD = 3.0V, WDT enabled, -40C to +85C VDD = 3.0V, WDT disabled, 0C to +70C VDD = 3.0V, WDT disabled, -40C to +85C
D010A D020 D021 D021A IPD Power-down Current (Note 3, 5)
-
22.5 7.5 0.9 0.9
48 30 5 5
Module Differential Current (Note 6) D022* IWDT Watchdog Timer D022A* IBOR Brown-out Reset
-
6.0 TBD
20 200
A A
WDTE BIT SET, VDD = 4.0V BODEN bit set, VDD = 5.0V
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: This is the limit to which VDD can be lowered without losing RAM data. 2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin loading and switching rate, oscillator type, internal code execution pattern, and temperature also have an impact on the current consumption. The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD, MCLR = VDD; WDT enabled/disabled as specified. 3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS. 4: For RC osc mode, current through Rext is not included. The current through the resistor can be estimated by the formula Ir = VDD/2Rext (mA) with Rext in kOhm. 5: Timer1 oscillator (when enabled) adds approximately 20 A to the specification. This value is from characterization and is for design guidance only. This is not tested. 6: The current is the additional current consumed when this peripheral is enabled. This current should be added to the base IDD or IPD measurement. 7: This is the voltage where the device enters the Brown-out Reset. When BOR is enabled, the device will perform a brown-out reset when VDD falls below VBOR.
(c) 1998 Microchip Technology Inc.
Preliminary
DS35008B-page 85
PIC16C62B/72A
13.3 DC Characteristics: PIC16C62B/72A-04 (Commercial, Industrial, Extended) PIC16C62B/72A-20 (Commercial, Industrial, Extended) PIC16LC62B/72A-04 (Commercial, Industrial)
Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial -40C TA +85C for industrial -40C TA +125C for extended Operating voltage VDD range as described in DC spec Section 13.1 and Section 13.2 Min Typ Max Units Conditions
DC CHARACTERISTICS
Param No.
Sym
Characteristic Input Low Voltage
VIL D030 D030A D031 D032 D033
I/O ports with TTL buffer with Schmitt Trigger buffer MCLR, OSC1 (in RC mode) OSC1 (in XT, HS and LP modes) Input High Voltage VSS Vss VSS Vss Vss 0.15VDD 0.8V 0.2VDD 0.2VDD 0.3VDD V V V V V Note1 For entire VDD range 4.5V VDD 5.5V
VIH D040 D040A
I/O ports with TTL buffer
D
2.0 0.25VD + 0.8V VDD Vdd V V 4.5V VDD 5.5V For entire VDD range
D041 D042 D042A D043
with Schmitt Trigger buffer MCLR OSC1 (XT, HS and LP modes) OSC1 (in RC mode) Input Leakage Current (Notes 2, 3)
0.8VDD 0.8VDD 0.7VDD 0.9VDD
-
VDD VDD VDD Vdd
V V V V
For entire VDD range Note1
D060 D061 D063 D070 D080
IIL
I/O ports MCLR, RA4/T0CKI OSC1
50 -
250 -
1 5 5 400 0.6
A A A A V
Vss VPIN VDD, Pin at hi-impedance Vss VPIN VDD Vss VPIN VDD, XT, HS and LP osc modes VDD = 5V, VPIN = VSS IOL = 8.5 mA, VDD = 4.5V, -40C to +85C
IPURB VOL
PORTB weak pull-up current Output Low Voltage I/O ports
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: In RC oscillator mode, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the device be driven with external clock in RC mode. 2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 3: Negative current is defined as current sourced by the pin.
DS35008B-page 86
Preliminary
(c) 1998 Microchip Technology Inc.
PIC16C62B/72A
Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial -40C TA +85C for industrial -40C TA +125C for extended Operating voltage VDD range as described in DC spec Section 13.1 and Section 13.2 Min D083 OSC2/CLKOUT (RC osc mode) Output High Voltage D090 VOH I/O ports (Note 3) VDD-0.7 VDD-0.7 D092 OSC2/CLKOUT (RC osc mode) VDD-0.7 VDD-0.7 D150* VOD Open-Drain High Voltage Capacitive Loading Specs on Output Pins D100 COSC2 OSC2 pin 15 pF In XT, HS and LP modes when external clock is used to drive OSC1. 8.5 V V V V V IOH = -3.0 mA, VDD = 4.5V, -40C to +85C IOH = -2.5 mA, VDD = 4.5V, -40C to +125C IOH = -1.3 mA, VDD = 4.5V, -40C to +85C IOH = -1.0 mA, VDD = 4.5V, -40C to +125C RA4 pin Typ Max 0.6 0.6 0.6 Units V V V Conditions IOL = 7.0 mA, VDD = 4.5V, -40C to +125C IOL = 1.6 mA, VDD = 4.5V, -40C to +85C IOL = 1.2 mA, VDD = 4.5V, -40C to +125C
DC CHARACTERISTICS
Param No.
Sym
Characteristic
D101 D102
CIO Cb
All I/O pins and OSC2 (in RC mode) SCL, SDA in I2C mode
-
-
50 400
pF pF
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: In RC oscillator mode, the OSC1/CLKIN pin is a Schmitt Trigger input. It is not recommended that the device be driven with external clock in RC mode. 2: The leakage current on the MCLR/VPP pin is strongly dependent on the applied voltage level. The specified levels represent normal operating conditions. Higher leakage current may be measured at different input voltages. 3: Negative current is defined as current sourced by the pin.
(c) 1998 Microchip Technology Inc.
Preliminary
DS35008B-page 87
PIC16C62B/72A
13.4
13.4.1
AC (Timing) Characteristics
TIMING PARAMETER SYMBOLOGY
The timing parameter symbols have been created following one of the following formats: 1. TppS2ppS 2. TppS T F pp cc ck cs di do dt io mc S F H I L I
2C
3. TCC:ST (I2C specifications only) 4. Ts (I2C specifications only) Time
Frequency
T
Lowercase letters (pp) and their meanings: CCP1 CLKOUT CS SDI SDO Data in I/O port MCLR osc rd rw sc ss t0 t1 wr OSC1 RD RD or WR SCK SS T0CKI T1CKI WR
Uppercase letters and their meanings: Fall High Invalid (Hi-impedance) Low only output access Bus free High Low High Low P R V Z Period Rise Valid Hi-impedance
AA BUF CC HD ST DAT STA
TCC:ST (I2C specifications only) Hold DATA input hold START condition SU STO Setup STOP condition
DS35008B-page 88
Preliminary
(c) 1998 Microchip Technology Inc.
PIC16C62B/72A
13.4.2 TIMING CONDITIONS The temperature and voltages specified in Table 13-1 apply to all timing specifications unless otherwise noted. Figure 13-4 specifies the load conditions for the timing specifications.
TABLE 13-1:
TEMPERATURE AND VOLTAGE SPECIFICATIONS - AC
Standard Operating Conditions (unless otherwise stated) Operating temperature 0C TA +70C for commercial -40C TA +85C for industrial -40C TA +125C for extended Operating voltage VDD range as described in DC spec Section 13.1 and Section 13.2. LC parts operate for commercial/industrial temp's only.
AC CHARACTERISTICS
FIGURE 13-4: LOAD CONDITIONS FOR DEVICE TIMING SPECIFICATIONS
Load condition 1 VDD/2 CL VSS Pin VSS CL RL = 464 CL = 50 pF 15 pF for all pins except OSC2/CLKOUT for OSC2 output Load condition 2
RL
Pin
(c) 1998 Microchip Technology Inc.
Preliminary
DS35008B-page 89
PIC16C62B/72A
13.4.3 TIMING DIAGRAMS AND SPECIFICATIONS
FIGURE 13-5: EXTERNAL CLOCK TIMING
Q4 OSC1 1 2 CLKOUT 3 3 4 4 Q1 Q2 Q3 Q4 Q1
TABLE 13-2:
Param No. 1A Sym Fosc
EXTERNAL CLOCK TIMING REQUIREMENTS
Characteristic External CLKIN Frequency (Note 1) Min DC DC DC DC Oscillator Frequency (Note 1) DC 0.1 4 5 Typ -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- Max 4 4 20 200 4 4 20 200 -- -- -- -- -- 10,000 250 250 -- DC -- -- -- 25 50 15 Units MHz MHz MHz kHz MHz MHz MHz kHz ns ns ns s ns ns ns ns s ns ns s ns ns ns ns Conditions RC and XT osc modes HS osc mode (-04) HS osc mode (-20) LP osc mode RC osc mode XT osc mode HS osc mode LP osc mode RC and XT osc modes HS osc mode (-04) HS osc mode (-20) LP osc mode RC osc mode XT osc mode HS osc mode (-04) HS osc mode (-20) LP osc mode TCY = 4/FOSC XT oscillator LP oscillator HS oscillator XT oscillator LP oscillator HS oscillator
1
Tosc
External CLKIN Period (Note 1)
250 250 50 5
Oscillator Period (Note 1)
250 250 250 50 5
2 3*
TCY TosL, TosH
Instruction Cycle Time (Note 1) External Clock in (OSC1) High or Low Time
200 100 2.5 15 -- -- --
4*
TosR, TosF
External Clock in (OSC1) Rise or Fall Time
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Instruction cycle period (TCY) equals four times the input oscillator time-base period. All specified values are based on characterization data for that particular oscillator type under standard operating conditions with the device executing code. Exceeding these specified limits may result in an unstable oscillator operation and/or higher than expected current consumption. All devices are tested to operate at "min." values with an external clock applied to the OSC1/CLKIN pin. When an external clock input is used, the "Max." cycle time limit is "DC" (no clock) for all devices.
DS35008B-page 90
Preliminary
(c) 1998 Microchip Technology Inc.
PIC16C62B/72A
FIGURE 13-6: CLKOUT AND I/O TIMING
Q4 OSC1 10 CLKOUT 13 14 I/O Pin (input) 17 I/O Pin (output) old value 15 new value 19 12 18 16 11 Q1 Q2 Q3
20, 21 Note: Refer to Figure 13-4 for load conditions.
TABLE 13-3:
Param Sym No.
10* 11* 12* 13* 14* 15* 16* 17* 18* 18A* 19* 20* 20A* 21* 21A* 22* 23*
CLKOUT AND I/O TIMING REQUIREMENTS
Characteristic Min -- -- -- -- -- Tosc + 200 0 -- 100 200 0 -- -- -- -- TCY TCY Typ 75 75 35 35 -- -- -- 50 -- -- -- 10 -- 10 -- -- -- Max 200 200 100 100 0.5TCY + 20 -- -- 150 -- -- -- 40 80 40 80 -- -- Units Conditions ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns Note 1 Note 1 Note 1 Note 1 Note 1 Note 1 Note 1
TosH2ckL OSC1 to CLKOUT TosH2ckH OSC1 to CLKOUT TckR TckF TckL2ioV TckH2ioI TosH2ioI CLKOUT rise time CLKOUT fall time CLKOUT to Port out valid Port in hold after CLKOUT OSC1 (Q2 cycle) to Port input invalid (I/O in hold time) Port output rise time Port output fall time INT pin high or low time RB7:RB4 change INT high or low time PIC16CXX PIC16LCXX
TioV2ckH Port in valid before CLKOUT TosH2ioV OSC1 (Q1 cycle) to Port out valid
TioV2osH Port input valid to OSC1 (I/O in setup time) TioR TioF Tinp Trbp PIC16CXX PIC16LCXX PIC16CXX PIC16LCXX
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. These parameters are asynchronous events not related to any internal clock edge. Note 1: Measurements are taken in RC Mode where CLKOUT output is 4 x TOSC.
(c) 1998 Microchip Technology Inc.
Preliminary
DS35008B-page 91
PIC16C62B/72A
FIGURE 13-7: RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER AND POWER-UP TIMER TIMING
VDD MCLR Internal POR 33 PWRT Time-out OSC Time-out Internal RESET Watchdog Timer RESET 34 I/O Pins Note: Refer to Figure 13-4 for load conditions. 32 30
31
34
FIGURE 13-8: BROWN-OUT RESET TIMING
BVDD VDD 35
TABLE 13-4:
Param No.
30 31* 32 33* 34 35
RESET, WATCHDOG TIMER, OSCILLATOR START-UP TIMER, POWER-UP TIMER AND BROWN-OUT RESET REQUIREMENTS
Characteristic MCLR Pulse Width (low) Watchdog Timer Time-out Period (No Prescaler) Oscillator Start-up Timer Period Power-up Timer Period I/O Hi-impedance from MCLR Low or WDT reset Brown-out Reset Pulse Width Min 2 7 -- 28 -- 100 Typ -- 18 1024 TOSC 72 -- -- Max -- 33 -- 132 2.1 -- Units s ms -- ms s s VDD BVDD (D005) Conditions VDD = 5V, -40C to +125C VDD = 5V, -40C to +125C TOSC = OSC1 period VDD = 5V, -40C to +125C
Sym TmcL Twdt Tost Tpwrt TIOZ TBOR
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested.
DS35008B-page 92
Preliminary
(c) 1998 Microchip Technology Inc.
PIC16C62B/72A
FIGURE 13-9: TIMER0 AND TIMER1 EXTERNAL CLOCK TIMINGS
T0CKI
40 42 T1OSO/T1CKI
41
45 47 TMR0 or TMR1 Note: Refer to Figure 13-4 for load conditions.
46 48
TABLE 13-5:
Param No. 40* Sym Tt0H
TIMER0 AND TIMER1 EXTERNAL CLOCK REQUIREMENTS
Characteristic T0CKI High Pulse Width No Prescaler With Prescaler Min 0.5TCY + 20 10 0.5TCY + 20 10 TCY + 40 Greater of: 20 or TCY + 40 N 0.5TCY + 20 15 25 30 50 0.5TCY + 20 15 25 30 50 GREATER OF: 30 OR TCY + 40 N GREATER OF: 50 OR TCY + 40 N 60 100 DC 2Tosc -- -- -- -- -- -- 200 7Tosc ns ns kHz -- Typ -- -- -- -- -- -- Max -- -- -- -- -- -- Units ns ns ns ns ns ns N = prescale value (2, 4,..., 256) Must also meet parameter 47 Conditions Must also meet parameter 42 Must also meet parameter 42
41*
Tt0L
T0CKI Low Pulse Width
No Prescaler With Prescaler
42*
Tt0P
T0CKI Period
No Prescaler With Prescaler
45*
Tt1H
T1CKI High Time
Synchronous, Prescaler = 1 Synchronous, Prescaler = 2,4,8 Asynchronous PIC16CXX PIC16LCXX PIC16CXX PIC16LCXX
-- -- -- -- -- -- -- -- -- -- --
-- -- -- -- -- -- -- -- -- -- --
ns ns ns ns ns ns ns ns ns ns ns
46*
Tt1L
T1CKI Low Time
Synchronous, Prescaler = 1 Synchronous, Prescaler = 2,4,8 Asynchronous PIC16CXX PIC16LCXX PIC16CXX PIC16LCXX
Must also meet parameter 47
47*
Tt1P
T1CKI input period
Synchronous
PIC16CXX
N = prescale value (1, 2, 4, 8) N = prescale value (1, 2, 4, 8)
PIC16LCXX
Asynchronous
PIC16CXX PIC16LCXX
Ft1 48 TCKEZtmr1
Timer1 oscillator input frequency range (oscillator enabled by setting bit T1OSCEN) Delay from external clock edge to timer increment
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested.
(c) 1998 Microchip Technology Inc.
Preliminary
DS35008B-page 93
PIC16C62B/72A
FIGURE 13-10: CAPTURE/COMPARE/PWM TIMINGS
CCP1 (Capture Mode)
50 52
51
CCP1 (Compare or PWM Mode) 53 Note: Refer to Figure 13-4 for load conditions. 54
TABLE 13-6:
Param No.
50*
CAPTURE/COMPARE/PWM REQUIREMENTS
Characteristic
CCP1 input low time No Prescaler With Prescaler No Prescaler With Prescaler PIC16CXX PIC16LCXX PIC16CXX PIC16LCXX
Sym
TccL
Min
0.5TCY + 20 10 20 0.5TCY + 20 10 20 3TCY + 40 N PIC16CXX PIC16LCXX PIC16CXX PIC16LCXX -- -- -- --
Typ Max Units
-- -- -- -- -- -- -- 10 25 10 25 -- -- -- -- -- -- -- 25 45 25 45 ns ns ns ns ns ns ns ns ns ns ns
Conditions
51*
TccH
CCP1 input high time
52* 53* 54*
TccP TccR TccF
CCP1 input period CCP1 output rise time CCP1 output fall time
N = prescale value (1,4, or 16)
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested.
DS35008B-page 94
Preliminary
(c) 1998 Microchip Technology Inc.
PIC16C62B/72A
FIGURE 13-11: EXAMPLE SPI MASTER MODE TIMING (CKE = 0)
SS 70 SCK (CKP = 0) 71 72
78
79
SCK (CKP = 1) 79 78
80 SDO MSb 75, 76 SDI MSb IN 74 73 BIT6 - - - -1
BIT6 - - - - - -1
LSb
LSb IN
Note:
Refer to Figure 13-4 for load conditions.
TABLE 13-7:
Param. No.
70 71 71A 72 72A 73 73A 74 75
EXAMPLE SPI MODE REQUIREMENTS (MASTER MODE, CKE = 0)
Characteristic Min TCY 1.25TCY + 30 40 1.25TCY + 30 40 100 1.5TCY + 40 100 -- -- --
PIC16CXX PIC16LCXX
Symbol
Typ Max Units -- -- -- -- -- -- -- -- 10 20 10 10 20 10 -- -- -- -- -- -- -- -- -- -- 25 45 25 25 45 25 50 100 ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
Conditions
TssL2scH, SS to SCK or SCK input TssL2scL TscH TscL TdiV2scH, TdiV2scL TB2B TscH2diL, TscL2diL TdoR TdoF TscR TscF SCK input high time (slave mode) SCK input low time (slave mode) Continuous Single Byte Continuous Single Byte
Note 1 Note 1
Setup time of SDI data input to SCK edge Last clock edge of Byte1 to the 1st clock edge of Byte2 Hold time of SDI data input to SCK edge SDO data output rise time PIC16CXX
PIC16LCXX
Note 1
76 78
SDO data output fall time SCK output rise time (master mode)
-- -- -- -- --
79 80
SCK output fall time (master mode)
PIC16CXX PIC16LCXX
TscH2doV, SDO data output valid TscL2doV after SCK edge
Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Specification 73A is only required if specifications 71A and 72A are used.
(c) 1998 Microchip Technology Inc.
Preliminary
DS35008B-page 95
PIC16C62B/72A
FIGURE 13-12: EXAMPLE SPI MASTER MODE TIMING (CKE = 1)
SS 81 SCK (CKP = 0) 71 73 SCK (CKP = 1) 80 78 72 79
SDO
MSb 75, 76
BIT6 - - - - - -1
LSb
SDI
MSb IN 74
BIT6 - - - -1
LSb IN
Note:
Refer to Figure 13-4 for load conditions.
TABLE 13-8:
Param. No.
71 71A 72 72A 73 73A 74 75
EXAMPLE SPI MODE REQUIREMENTS (MASTER MODE, CKE = 1)
Characteristic SCK input high time (slave mode) SCK input low time (slave mode) Continuous Single Byte Continuous Single Byte Min 1.25TCY + 30 40 1.25TCY + 30 40 100 1.5TCY + 40 100 -- --
PIC16CXX PIC16LCXX
Symbol TscH TscL TdiV2scH, TdiV2scL TB2B TscH2diL, TscL2diL TdoR TdoF TscR TscF
Typ Max Units -- -- -- -- -- -- -- 10 20 10 10 20 10 -- -- -- -- -- -- -- -- -- -- 25 45 25 25 45 25 50 100 -- ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
Conditions
Note 1 Note 1
Setup time of SDI data input to SCK edge Last clock edge of Byte1 to the 1st clock edge of Byte2 Hold time of SDI data input to SCK edge SDO data output rise time SDO data output fall time SCK output rise time (master mode)
PIC16CXX PIC16LCXX
Note 1
76 78
-- -- -- TCY
79 80
SCK output fall time (master mode)
PIC16CXX PIC16LCXX
TscH2doV, SDO data output valid TscL2doV after SCK edge
81
TdoV2scH, SDO data output setup to SCK edge TdoV2scL
Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Specification 73A is only required if specifications 71A and 72A are used.
DS35008B-page 96
Preliminary
(c) 1998 Microchip Technology Inc.
PIC16C62B/72A
FIGURE 13-13: EXAMPLE SPI SLAVE MODE TIMING (CKE = 0)
SS 70 SCK (CKP = 0) 71 72 83
78
79
SCK (CKP = 1) 79 78
80 SDO MSb 75, 76 SDI MSb IN 74 73 BIT6 - - - -1
BIT6 - - - - - -1
LSb 77 LSb IN
Note:
Refer to Figure 13-4 for load conditions.
TABLE 13-9:
Param. No.
70 71 71A 72 72A 73 73A 74 75
EXAMPLE SPI MODE REQUIREMENTS (SLAVE MODE TIMING (CKE = 0)
Characteristic Min TCY 1.25TCY + 30 40 1.25TCY + 30 40 100 1.5TCY + 40 100 -- -- 10 -- -- -- 1.5TCY + 40
PIC16CXX PIC16LCXX
Symbol
Typ Max Units -- -- -- -- -- -- -- -- 10 20 10 -- 10 20 10 -- -- -- -- -- -- -- -- -- -- -- 25 45 25 50 25 45 25 50 100 -- ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
Conditions
TssL2scH, SS to SCK or SCK input TssL2scL TscH TscL TdiV2scH, TdiV2scL TB2B TscH2diL, TscL2diL TdoR TdoF TssH2doZ TscR TscF SCK input high time (slave mode) SCK input low time (slave mode) Continuous Single Byte Continuous Single Byte
Note 1 Note 1
Setup time of SDI data input to SCK edge Last clock edge of Byte1 to the 1st clock edge of Byte2 Hold time of SDI data input to SCK edge SDO data output rise time PIC16CXX
PIC16LCXX
Note 1
76 77 78
SDO data output fall time SS to SDO output hi-impedance SCK output rise time (master mode)
79 80
SCK output fall time (master mode)
PIC16CXX PIC16LCXX
TscH2doV, SDO data output valid TscL2doV after SCK edge TscH2ssH, SS after SCK edge TscL2ssH
83
Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Specification 73A is only required if specifications 71A and 72A are used.
(c) 1998 Microchip Technology Inc.
Preliminary
DS35008B-page 97
PIC16C62B/72A
FIGURE 13-14: EXAMPLE SPI SLAVE MODE TIMING (CKE = 1)
82 SS
SCK (CKP = 0)
70 83 71 72
SCK (CKP = 1) 80
SDO
MSb 75, 76
BIT6 - - - - - -1
LSb 77
SDI
MSb IN
BIT6 - - - -1
LSb IN
74 NOTE: Refer to Figure 13-4 for load conditions.
TABLE 13-10: EXAMPLE SPI SLAVE MODE REQUIREMENTS (CKE = 1)
Param. No.
70 71 71A 72 72A 73A 74 75
Symbol TssL2scH, TssL2scL TscH TscL TB2B TscH2diL, TscL2diL TdoR TdoF TssH2doZ TscR TscF
Characteristic SS to SCK or SCK input SCK input high time (slave mode) SCK input low time (slave mode) Continuous Single Byte Continuous Single Byte
Min TCY 1.25TCY + 30 40 1.25TCY + 30 40 1.5TCY + 40 100 -- -- 10 -- -- -- -- -- -- -- 1.5TCY + 40
Typ Max Units -- -- -- -- -- -- -- 10 20 10 -- 10 20 10 -- -- -- -- -- -- -- -- -- -- -- -- 25 45 25 50 25 45 25 50 100 50 100 -- ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
Conditions
Note 1 Note 1 Note 1
Last clock edge of Byte1 to the 1st clock edge of Byte2 Hold time of SDI data input to SCK edge SDO data output rise time SDO data output fall time SS to SDO output hi-impedance SCK output rise time (master mode)
PIC16CXX PIC16LCXX PIC16CXX PIC16LCXX
76 77 78
79 80
SCK output fall time (master mode)
PIC16CXX PIC16LCXX PIC16CXX PIC16LCXX
TscH2doV, SDO data output valid TscL2doV after SCK edge TssL2doV SDO data output valid after SS edge
82
83
TscH2ssH, SS after SCK edge TscL2ssH
Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: Specification 73A is only required if specifications 71A and 72A are used.
DS35008B-page 98
Preliminary
(c) 1998 Microchip Technology Inc.
PIC16C62B/72A
FIGURE 13-15: I2C BUS START/STOP BITS TIMING
SCL 90 SDA
91 92
93
START Condition
STOP Condition
Note:
Refer to Figure 13-4 for load conditions.
TABLE 13-11: I2C BUS START/STOP BITS REQUIREMENTS
Parameter No.
90*
Sym TSU:STA THD:STA TSU:STO THD:STO
Characteristic START condition Setup time START condition Hold time STOP condition Setup time STOP condition Hold time 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode
Min 4700 600 4000 600 4700 600 4000 600
Ty Max Unit p s -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- ns ns ns ns
Conditions Only relevant for repeated START condition After this period the first clock pulse is generated
91*
92*
93
*
These parameters are characterized but not tested.
(c) 1998 Microchip Technology Inc.
Preliminary
DS35008B-page 99
PIC16C62B/72A
FIGURE 13-16: I2C BUS DATA TIMING
103 SCL 100 101 90 91 SDA In 110 109 SDA Out 109 106 107 92 102
Note:
Refer to Figure 13-4 for load conditions.
TABLE 13-12: I2C BUS DATA REQUIREMENTS
Param. No. 100* Sym THIGH Characteristic Clock high time 100 kHz mode 400 kHz mode SSP Module 101* TLOW Clock low time 100 kHz mode 400 kHz mode SSP Module 102* TR SDA and SCL rise time SDA and SCL fall time START condition setup time START condition hold time Data input hold time Data input setup time 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode 107* 92* 109* 110* TSU:DAT TSU:STO TAA TBUF 100 kHz mode 400 kHz mode STOP condition setup 100 kHz mode time 400 kHz mode Output valid from clock Bus free time 100 kHz mode 400 kHz mode 100 kHz mode 400 kHz mode Cb Bus capacitive loading Min 4.0 0.6 1.5TCY 4.7 1.3 1.5TCY -- 20 + 0.1Cb -- 20 + 0.1Cb 4.7 0.6 4.0 0.6 0 0 250 100 4.7 0.6 -- -- 4.7 1.3 -- Max -- -- -- -- -- -- 1000 300 300 300 -- -- -- -- -- 0.9 -- -- -- -- 3500 -- -- -- 400 ns ns ns ns s s s s ns s ns ns s s ns ns s s pF Time the bus must be free before a new transmission can start Note 1 Note 2 Cb is specified to be from 10-400 pF Only relevant for repeated START condition After this period the first clock pulse is generated Cb is specified to be from 10-400 pF s s Device must operate at a minimum of 1.5 MHz Device must operate at a minimum of 10 MHz Units s s Conditions Device must operate at a minimum of 1.5 MHz Device must operate at a minimum of 10 MHz
103*
TF
90* 91* 106*
TSU:STA THD:STA THD:DAT
* These parameters are characterized but not tested. Note 1: As a transmitter, the device must provide this internal minimum delay time to bridge the undefined region (min. 300 ns) of the falling edge of SCL to avoid unintended generation of START or STOP conditions. 2: A fast-mode (400 kHz) I2C-bus device can be used in a standard-mode (100 kHz) I2C-bus system, but the requirement Tsu:DAT 250 ns must then be met. This will automatically be the case if the device does not stretch the LOW period of the SCL signal. If such a device does stretch the LOW period of the SCL signal, it must output the next data bit to the SDA line TR max.+tsu;DAT = 1000 + 250 = 1250 ns (according to the standard-mode I2C bus specification) before the SCL line is released.
DS35008B-page 100
Preliminary
(c) 1998 Microchip Technology Inc.
PIC16C62B/72A
TABLE 13-13: A/D CONVERTER CHARACTERISTICS: PIC16C72A-04 (COMMERCIAL, INDUSTRIAL, EXTENDED) PIC16C72A-20 (COMMERCIAL, INDUSTRIAL, EXTENDED) PIC16LC72A-04 (COMMERCIAL, INDUSTRIAL)
Param Sym No. A01 A02 A03 A04 A05 A06 A10 A20 A25 A30 A40 NR Resolution Characteristic Min -- -- -- -- -- -- -- 2.5V VSS - 0.3 -- -- -- 10 Typ -- -- -- -- -- -- guaranteed (Note 3) -- -- -- 180 90 -- Max 8-bits <1 <1 <1 <1 <1 -- VDD + 0.3 VREF + 0.3 10.0 -- -- 1000 Units bit LSB LSB LSB LSB LSB -- V V k A A A Average current consumption when A/D is on. (Note 1) During VAIN acquisition. Based on differential of VHOLD to VAIN to charge CHOLD, see Section 9.1. During A/D conversion cycle Conditions VREF = VDD = 5.12V, VSS VAIN VREF VREF = VDD = 5.12V, VSS VAIN VREF VREF = VDD = 5.12V, VSS VAIN VREF VREF = VDD = 5.12V, VSS VAIN VREF VREF = VDD = 5.12V, VSS VAIN VREF VREF = VDD = 5.12V, VSS VAIN VREF VSS VAIN VREF
EABS Total Absolute error EIL EDL EFS Integral linearity error Differential linearity error Full scale error
EOFF Offset error -- Monotonicity
VREF Reference voltage VAIN ZAIN IAD Analog input voltage Recommended impedance of analog voltage source A/D conversion current (VDD) PIC16CXX PIC16LCXX
A50
IREF
VREF input current (Note 2)
--
--
10
A
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: When A/D is off, it will not consume any current other than minor leakage current. The power-down current spec includes any such leakage from the A/D module. 2: VREF current is from RA3 pin or VDD pin, whichever is selected as reference input. 3: The A/D conversion result never decreases with an increase in the Input Voltage and has no missing codes.
(c) 1998 Microchip Technology Inc.
Preliminary
DS35008B-page 101
PIC16C62B/72A
FIGURE 13-17: A/D CONVERSION TIMING
BSF ADCON0, GO 134 Q4 130 A/D CLK A/D DATA ADRES ADIF GO SAMPLE SAMPLING STOPPED DONE 132 7 6 5 4 3 2 1 0 NEW_DATA 1 TCY (Tosc/2) (1) 131
OLD_DATA
Note 1: If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the SLEEP instruction to be executed.
TABLE 13-14: A/D CONVERSION REQUIREMENTS
Param Sym No.
130
Characteristic A/D clock period
PIC16CXX PIC16LCXX PIC16CXX PIC16LCXX
Min 1.6 2.0 2.0 3.0 11 Note 2 5*
Typ -- -- 4.0 6.0 -- 20 --
Max -- -- 6.0 9.0 11 -- --
Unit s s s s s TAD s s
Conditions TOSC based, VREF 3.0V TOSC based, VREF full range A/D RC Mode A/D RC Mode
TAD
131 132
TCNV Conversion time (not including S/H time) (Note 1) TACQ Acquisition time
The minimum time is the amplifier settling time. This may be used if the "new" input voltage has not changed by more than 1 LSb (i.e., 20.0 mV @ 5.12V) from the last sampled voltage (as stated on CHOLD). If the A/D clock source is selected as RC, a time of TCY is added before the A/D clock starts. This allows the SLEEP instruction to be executed.
134
TGO
Q4 to A/D clock start
--
TOSC/2
--
--
135
Tswc Switching from convert sample time
1.5
--
--
TAD
* These parameters are characterized but not tested. Data in "Typ" column is at 5V, 25C unless otherwise stated. These parameters are for design guidance only and are not tested. Note 1: ADRES register may be read on the following TCY cycle. 2: See Section 9.1 for min conditions.
DS35008B-page 102
Preliminary
(c) 1998 Microchip Technology Inc.
PIC16C62B/72A
14.0 DC AND AC CHARACTERISTICS GRAPHS AND TABLES
The graphs and tables provided in this section are for design guidance and are not tested. In some graphs or tables, the data presented are outside specified operating range (i.e., outside specified VDD range). This is for information only and devices are guaranteed to operate properly only within the specified range. The data presented in this section is a statistical summary of data collected on units from different lots over a period of time and matrix samples. 'Typical' represents the mean of the distribution at 25C. 'Max' or 'min' represents (mean + 3) or (mean - 3) respectively, where is standard deviation, over the whole temperature range.
Graphs and Tables not available at this time.
Data is not available at this time but you may reference the PIC16C72 Series Data Sheet (DS39016,) DC and AC characteristic section, which contains data similar to what is expected.
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 103
PIC16C62B/72A
NOTES:
DS35008B-page 104
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
15.0
15.1
PACKAGING INFORMATION
Package Marking Information 28-Lead PDIP (Skinny DIP) MMMMMMMMMMMM XXXXXXXXXXXXXXX AABBCDE Example PIC16C72A-04/SP 9917HAT
28-Lead CERDIP Windowed XXXXXXXXXXX XXXXXXXXXXX XXXXXXXXXXX AABBCDE
Example PIC16C72A/JW 9917CAT
28-Lead SOIC MMMMMMMMMMMMMMMM XXXXXXXXXXXXXXXXXXXX AABBCDE
Example PIC16C62B-20/SO 9910/SAA
28-Lead SSOP
XXXXXXXXXXXX XXXXXXXXXXXX
Example
PIC16C62B 20I/SS025
AABBCDE
9917SBP
Legend: MM...M XX...X AA BB C
D E
Microchip part number information Customer specific information* Year code (last 2 digits of calendar year) Week code (week of January 1 is week `01') Facility code of the plant at which wafer is manufactured O = Outside Vendor C = 5" Line S = 6" Line H = 8" Line Mask revision number Assembly code of the plant or country of origin in which part was assembled
Note:
In the event the full Microchip part number cannot be marked on one line, it will be carried over to the next line thus limiting the number of available characters for customer specific information.
*
Standard OTP marking consists of Microchip part number, year code, week code, facility code, mask rev#, and assembly code. For OTP marking beyond this, certain price adders apply. Please check with your Microchip Sales Office. For QTP devices, any special marking adders are included in QTP price.
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 105
PIC16C62B/72A
15.2 28-Lead Skinny Plastic Dual In-line (SP) - 300 mil (PDIP)
E1
D
2 n E A c eB Units Dimension Limits n p A1 B1 B INCHES* NOM 28 .100 .150 .130 p MILLIMETERS NOM 28 2.54 3.56 3.81 3.18 3.30 0.38 7.62 7.94 7.09 7.80 34.16 34.67 3.18 3.30 0.20 0.29 1.02 1.33 0.41 0.48 8.13 8.89 5 10 5 10 L 1 A2
MIN
MAX
MIN
MAX
Number of Pins Pitch Top to Seating Plane A .140 .160 Molded Package Thickness A2 .125 .135 Base to Seating Plane A1 .015 Shoulder to Shoulder Width E .300 .313 .325 Molded Package Width E1 .279 .307 .335 Overall Length D 1.345 1.365 1.385 Tip to Seating Plane L .125 .130 .135 c Lead Thickness .008 .012 .015 Upper Lead Width B1 .040 .053 .065 Lower Lead Width B .016 .019 .022 Overall Row Spacing eB .320 .350 .430 Mold Draft Angle Top 5 10 15 Mold Draft Angle Bottom 5 10 15 *Controlling Parameter Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MO-095 Drawing No. C04-070
4.06 3.43 8.26 8.51 35.18 3.43 0.38 1.65 0.56 10.92 15 15
DS35008B-page 106
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
15.3 28-Lead Ceramic Dual In-line with Window (JW) - 300 mil (CERDIP)
E1
W2
D
2 n W1 E A c A1 Units Dimension Limits n p A A2 A1 E E1 D L c B1 B eB W1 W2 INCHES* NOM 28 .100 .183 .160 .023 .313 .290 1.458 .140 .010 .058 .019 .385 .140 .300 B1 B MIN MAX A2 L eB 1
p MILLIMETERS MIN NOM 28 2.54 4.32 4.64 3.94 4.06 0.38 0.57 7.62 7.94 7.24 7.37 36.32 37.02 3.43 3.56 0.20 0.25 1.27 1.46 0.41 0.47 8.76 9.78 3.30 3.56 7.37 7.62
MAX
Number of Pins Pitch Top to Seating Plane Ceramic Package Height Standoff Shoulder to Shoulder Width Ceramic Pkg. Width Overall Length Tip to Seating Plane Lead Thickness Upper Lead Width Lower Lead Width Overall Row Spacing Window Width Window Length *Controlling Parameter JEDEC Equivalent: MO-058 Drawing No. C04-080
.170 .155 .015 .300 .285 1.430 .135 .008 .050 .016 .345 .130 .290
.195 .165 .030 .325 .295 1.485 .145 .012 .065 .021 .425 .150 .310
4.95 4.19 0.76 8.26 7.49 37.72 3.68 0.30 1.65 0.53 10.80 3.81 7.87
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 107
PIC16C62B/72A
15.4 28-Lead Plastic Small Outline (SO) - Wide, 300 mil (SOIC)
E E1 p
D
B n h 45 c A Units Dimension Limits n p L A1 INCHES* NOM 28 .050 .099 .091 .008 .407 .295 .704 .020 .033 4 .011 .017 12 12 MILLIMETERS NOM 28 1.27 2.36 2.50 2.24 2.31 0.10 0.20 10.01 10.34 7.32 7.49 17.65 17.87 0.25 0.50 0.41 0.84 0 4 0.23 0.28 0.36 0.42 0 12 0 12 A2 2 1
MIN
MAX
MIN
MAX
Number of Pins Pitch Overall Height A .093 .104 Molded Package Thickness A2 .088 .094 Standoff A1 .004 .012 Overall Width E .394 .420 Molded Package Width E1 .288 .299 Overall Length D .695 .712 Chamfer Distance h .010 .029 Foot Length L .016 .050 Foot Angle Top 0 8 c Lead Thickness .009 .013 Lead Width B .014 .020 Mold Draft Angle Top 0 15 Mold Draft Angle Bottom 0 15 *Controlling Parameter Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MS-013 Drawing No. C04-052
2.64 2.39 0.30 10.67 7.59 18.08 0.74 1.27 8 0.33 0.51 15 15
DS35008B-page 108
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
15.5 28-Lead Plastic Shrink Small Outline (SS) - 209 mil, 5.30 mm (SSOP)
E E1 p
D
B n 2 1
A c A2
L
A1
Number of Pins Pitch Overall Height A .068 .078 Molded Package Thickness A2 .064 .072 Standoff A1 .002 .010 Overall Width E .299 .319 Molded Package Width E1 .201 .212 Overall Length D .396 .407 Foot Length L .022 .037 c Lead Thickness .004 .010 Foot Angle 0 8 Lead Width B .010 .015 Mold Draft Angle Top 0 10 Mold Draft Angle Bottom 0 10 *Controlling Parameter Notes: Dimensions D and E1 do not include mold flash or protrusions. Mold flash or protrusions shall not exceed .010" (0.254mm) per side. JEDEC Equivalent: MS-150 Drawing No. C04-073
Units Dimension Limits n p
MIN
INCHES NOM 28 .026 .073 .068 .006 .309 .207 .402 .030 .007 4 .013 5 5
MAX
MIN
MILLIMETERS* NOM MAX 28 0.66 1.73 1.85 1.98 1.63 1.73 1.83 0.05 0.15 0.25 7.59 7.85 8.10 5.11 5.25 5.38 10.06 10.20 10.34 0.56 0.75 0.94 0.10 0.18 0.25 0.00 101.60 203.20 0.25 0.32 0.38 0 5 10 0 5 10
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 109
PIC16C62B/72A
NOTES:
DS35008B-page 110
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
APPENDIX A: REVISION HISTORY
Version A Date 7/98 Revision Description This is a new data sheet. However, the devices described in this data sheet are the upgrades to the devices found in the PIC16C6X Data Sheet, DS30234, and the PIC16C7X Data Sheet, DS30390.
APPENDIX B: CONVERSION CONSIDERATIONS
Considerations for converting from previous versions of devices to the ones listed in this data sheet are listed in Table B-1.
TABLE B-1:
CONVERSION CONSIDERATIONS PIC16C62A/72
2.5V - 6.0V Basic SSP (2 mode SPI) CCP does not reset TMR1 when in special event trigger mode. Writing to TMR1L register can cause overflow in TMR1H register. 2.5V - 5.5V SSP (4 mode SPI) N/A N/A
Difference
Voltage Range SSP module CCP module Timer1 module
PIC16C62B/72A
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 111
PIC16C62B/72A
APPENDIX C: MIGRATION FROM BASE-LINE TO MID-RANGE DEVICES
This section discusses how to migrate from a baseline device (i.e., PIC16C5X) to a mid-range device (i.e., PIC16CXXX). The following are the list of modifications over the PIC16C5X microcontroller family: Instruction word length is increased to 14-bits. This allows larger page sizes both in program memory (2K now as opposed to 512 before) and register file (128 bytes now versus 32 bytes before). 2. A PC high latch register (PCLATH) is added to handle program memory paging. Bits PA2, PA1, PA0 are removed from STATUS register. 3. Data memory paging is redefined slightly. STATUS register is modified. 4. Four new instructions have been added: RETURN, RETFIE, ADDLW, and SUBLW. Two instructions TRIS and OPTION are being phased out although they are kept for compatibility with PIC16C5X. 5. OPTION_REG and TRIS registers are made addressable. 6. Interrupt capability is added. Interrupt vector is at 0004h. 7. Stack size is increased to 8 deep. 8. Reset vector is changed to 0000h. 9. Reset of all registers is revisited. Five different reset (and wake-up) types are recognized. Registers are reset differently. 10. Wake up from SLEEP through interrupt is added. 1. 11. Two separate timers, Oscillator Start-up Timer (OST) and Power-up Timer (PWRT) are included for more reliable power-up. These timers are invoked selectively to avoid unnecessary delays on power-up and wake-up. 12. PORTB has weak pull-ups and interrupt on change feature. 13. T0CKI pin is also a port pin (RA4) now. 14. FSR is made a full eight bit register. 15. "In-circuit serial programming" is made possible. The user can program PIC16CXX devices using only five pins: VDD, VSS, MCLR/VPP, RB6 (clock) and RB7 (data in/out). 16. PCON status register is added with a Power-on Reset status bit (POR). 17. Code protection scheme is enhanced such that portions of the program memory can be protected, while the remainder is unprotected. 18. Brown-out protection circuitry has been added. Controlled by configuration word bit BODEN. Brown-out reset ensures the device is placed in a reset condition if VDD dips below a fixed setpoint. To convert code written for PIC16C5X to PIC16CXXX, the user should take the following steps: 1. 2. Remove any program memory page select operations (PA2, PA1, PA0 bits) for CALL, GOTO. Revisit any computed jump operations (write to PC or add to PC, etc.) to make sure page bits are set properly under the new scheme. Eliminate any data memory page switching. Redefine data variables to reallocate them. Verify all writes to STATUS, OPTION, and FSR registers since these have changed. Change reset vector to 0000h.
3. 4. 5.
DS35008B-page 112
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
INDEX A
A/D ..................................................................................... 49 A/D Converter Enable (ADIE Bit) ............................... 14 A/D Converter Flag (ADIF Bit) ............................ 15, 51 A/D Converter Interrupt, Configuring ......................... 51 ADCON0 Register ................................................ 9, 49 ADCON1 Register ........................................10, 49, 50 ADRES Register .............................................9, 49, 51 Analog Port Pins .......................................................... 6 Analog Port Pins, Configuring ................................... 53 Block Diagram ........................................................... 51 Block Diagram, Analog Input Model .......................... 52 Channel Select (CHS2:CHS0 Bits) ............................ 49 Clock Select (ADCS1:ADCS0 Bits) ........................... 49 Configuring the Module ............................................. 51 Conversion Clock (TAD) ............................................. 53 Conversion Status (GO/DONE Bit) ..................... 49, 51 Conversions ............................................................... 54 Converter Characteristics ........................................ 101 Module On/Off (ADON Bit) ........................................ 49 Port Configuration Control (PCFG2:PCFG0 Bits) ...... 50 Sampling Requirements ............................................ 52 Special Event Trigger (CCP) .............................. 35, 54 Timing Diagram ....................................................... 102 Absolute Maximum Ratings ............................................... 81 ADCON0 Register ........................................................ 9, 49 ADCS1:ADCS0 Bits ................................................... 49 ADON Bit ................................................................... 49 CHS2:CHS0 Bits ....................................................... 49 GO/DONE Bit ..................................................... 49, 51 ADCON1 Register ................................................10, 49, 50 PCFG2:PCFG0 Bits ................................................... 50 ADRES Register .....................................................9, 49, 51 Architecture PIC16C62B/PIC16C72A Block Diagram ..................... 5 Assembler MPASM Assembler ................................................... 75 CCP1CON Register .......................................................... 33 CCP1M3:CCP1M0 Bits ............................................. 33 CCP1X:CCP1Y Bits .................................................. 33 Code Protection ...........................................................55, 66 CP1:CP0 Bits ............................................................ 55 Compare (CCP Module) .................................................... 35 Block Diagram ........................................................... 35 CCP Pin Configuration .............................................. 35 CCPR1H:CCPR1L Registers .................................... 35 Software Interrupt ...................................................... 35 Special Event Trigger ................................... 29, 35, 54 Timer1 Mode Selection ............................................. 35 Configuration Bits .............................................................. 55 Conversion Considerations ............................................. 111
D
Data Memory ....................................................................... 8 Bank Select (RP1:RP0 Bits) ..................................8, 11 General Purpose Registers ......................................... 8 Register File Map ........................................................ 8 Special Function Registers ......................................... 9 DC Characteristics ......................................................84, 86 Development Support ........................................................ 75 Direct Addressing .............................................................. 18
E
Electrical Characteristics ................................................... 81 Errata ................................................................................... 3 External Power-on Reset Circuit ....................................... 59
F
Firmware Instructions ........................................................ 67
I
I/O Ports ............................................................................ 19 I2C (SSP Module) .............................................................. 41 ACK Pulse .......................................41, 42, 43, 44, 45 Addressing ................................................................ 42 Block Diagram ........................................................... 41 Buffer Full Status (BF Bit) ......................................... 46 Clock Polarity Select (CKP Bit) ................................. 47 Data/Address (D/A Bit) .............................................. 46 Master Mode ............................................................. 45 Mode Select (SSPM3:SSPM0 Bits) .......................... 47 Multi-Master Mode .................................................... 45 Read/Write Bit Information (R/W Bit) .... 42, 43, 44, 46 Receive Overflow Indicator (SSPOV Bit) .................. 47 Reception .................................................................. 43 Reception Timing Diagram ........................................ 43 Slave Mode ............................................................... 41 Start (S Bit) ..........................................................45, 46 Stop (P Bit) ..........................................................45, 46 Synchronous Serial Port Enable (SSPEN Bit) .......... 47 Timing Diagram, Data ............................................. 100 Timing Diagram, Start/Stop Bits ................................ 99 Transmission ............................................................. 44 Update Address (UA Bit) ........................................... 46 ID Locations ................................................................55, 66 In-Circuit Serial Programming (ICSP) .........................55, 66 Indirect Addressing ............................................................ 18 FSR Register .................................................... 8, 9, 18 INDF Register ............................................................. 9 Instruction Format ............................................................. 67
B
Banking, Data Memory ................................................. 8, 11 Brown-out Reset (BOR) .......................... 55, 57, 59, 60, 61 BOR Enable (BODEN Bit) ......................................... 55 BOR Status (BOR Bit) ............................................... 16 Timing Diagram ......................................................... 92
C
Capture (CCP Module) ...................................................... 34 Block Diagram ........................................................... 34 CCP Pin Configuration .............................................. 34 CCPR1H:CCPR1L Registers .................................... 34 Changing Between Capture Prescalers .................... 34 Software Interrupt ...................................................... 34 Timer1 Mode Selection .............................................. 34 Capture/Compare/PWM Interaction of Two CCP Modules ............................... 33 Capture/Compare/PWM (CCP) ......................................... 33 CCP1CON Register .............................................. 9, 33 CCPR1H Register ................................................ 9, 33 CCPR1L Register ................................................. 9, 33 Enable (CCP1IE Bit) .................................................. 14 Flag (CCP1IF Bit) ...................................................... 15 RC2/CCP1 Pin ............................................................. 6 Timer Resources ....................................................... 33 Timing Diagram ......................................................... 94
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 113
PIC16C62B/72A
Instruction Set .................................................................... 67 ADDLW ...................................................................... 69 ADDWF ...................................................................... 69 ANDLW ...................................................................... 69 ANDWF ...................................................................... 69 BCF ............................................................................ 69 BSF ............................................................................ 69 BTFSC ....................................................................... 70 BTFSS ....................................................................... 70 CALL .......................................................................... 70 CLRF ......................................................................... 70 CLRW ......................................................................... 70 CLRWDT ................................................................... 70 COMF ........................................................................ 71 DECF ......................................................................... 71 DECFSZ .................................................................... 71 GOTO ........................................................................ 71 INCF .......................................................................... 71 INCFSZ ...................................................................... 71 IORLW ....................................................................... 72 IORWF ....................................................................... 72 MOVF ........................................................................ 72 MOVLW ..................................................................... 72 MOVWF ..................................................................... 72 NOP ........................................................................... 72 RETFIE ...................................................................... 73 RETLW ...................................................................... 73 RETURN .................................................................... 73 RLF ............................................................................ 73 RRF ........................................................................... 73 SLEEP ....................................................................... 73 SUBLW ...................................................................... 74 SUBWF ...................................................................... 74 SWAPF ...................................................................... 74 XORLW ...................................................................... 74 XORWF ..................................................................... 74 Summary Table ......................................................... 68 INTCON Register .......................................................... 9, 13 GIE Bit ....................................................................... 13 INTE Bit ..................................................................... 13 INTF Bit ...................................................................... 13 PEIE Bit ..................................................................... 13 RBIE Bit ..................................................................... 13 RBIF Bit .............................................................. 13, 21 T0IE Bit ...................................................................... 13 T0IF Bit ...................................................................... 13 Interrupt Sources ........................................................ 55, 62 A/D Conversion Complete ......................................... 51 Block Diagram ........................................................... 62 Capture Complete (CCP) ........................................... 34 Compare Complete (CCP) ......................................... 35 Interrupt on Change (RB7:RB4 ) ............................... 21 RB0/INT Pin, External ........................................... 6, 63 SSP Receive/Transmit Complete .............................. 39 TMR0 Overflow ................................................... 26, 63 TMR1 Overflow ................................................... 27, 29 TMR2 to PR2 Match .................................................. 32 TMR2 to PR2 Match (PWM) ............................... 31, 36 Interrupts, Context Saving During ...................................... 63 Interrupts, Enable Bits A/D Converter Enable (ADIE Bit) ............................... 14 CCP1 Enable (CCP1IE Bit) ....................................... 14 Global Interrupt Enable (GIE Bit) ........................ 13, 62 Interrupt on Change (RB7:RB4) Enable (RBIE Bit) ................................................ 13, 63 Peripheral Interrupt Enable (PEIE Bit) ....................... 13 RB0/INT Enable (INTE Bit) ........................................ 13 SSP Enable (SSPIE Bit) ............................................ 14 TMR0 Overflow Enable (T0IE Bit) ............................. 13 TMR1 Overflow Enable (TMR1IE Bit) ....................... 14 TMR2 to PR2 Match Enable (TMR2IE Bit) ................ 14 Interrupts, Flag Bits A/D Converter Flag (ADIF Bit) .............................15, 51 CCP1 Flag (CCP1IF Bit) .............................. 15, 34, 35 Interrupt on Change (RB7:RB4) Flag (RBIF Bit) .............................................. 13, 21, 63 RB0/INT Flag (INTF Bit) ............................................ 13 SSP Flag (SSPIF Bit) ................................................ 15 TMR0 Overflow Flag (T0IF Bit) ...........................13, 63 TMR1 Overflow Flag (TMR1IF Bit) ............................ 15 TMR2 to PR2 Match Flag (TMR2IF Bit) .................... 15
K
KeeLoq(R) Evaluation and Programming Tools .................. 78
M
Master Clear (MCLR) .......................................................... 6 MCLR Reset, Normal Operation .................. 57, 60, 61 MCLR Reset, SLEEP ................................... 57, 60, 61 Memory Organization Data Memory ............................................................... 8 Program Memory ......................................................... 7 MPLAB Integrated Development Environment Software .. 75
O
OPCODE Field Descriptions ............................................. 67 OPTION_REG Register ..............................................10, 12 INTEDG Bit ................................................................ 12 PS2:PS0 Bits .......................................................12, 25 PSA Bit ................................................................12, 25 RBPU Bit ................................................................... 12 T0CS Bit ..............................................................12, 25 T0SE Bit ..............................................................12, 25 OSC1/CLKIN Pin ................................................................. 6 OSC2/CLKOUT Pin .............................................................. 6 Oscillator Configuration ...............................................55, 56 HS .......................................................................56, 60 LP ........................................................................56, 60 RC .................................................................. 6, 57, 60 Selection (FOSC1:FOSC0 Bits).................................. 55 XT ........................................................................56, 60 Oscillator, Timer1 ........................................................27, 29 Oscillator, WDT ................................................................. 64
P
Packaging ........................................................................ 105 Paging, Program Memory .............................................7, 17 PCON Register ............................................................16, 60 BOR Bit ..................................................................... 16 POR Bit ..................................................................... 16 PICDEM-1 Low-Cost PICmicro Demo Board .................... 77 PICDEM-2 Low-Cost PIC16CXX Demo Board ................. 77 PICDEM-3 Low-Cost PIC16CXXX Demo Board ............... 77 PICSTART(R) Plus Entry Level Development System ........ 77 PIE1 Register ..............................................................10, 14 ADIE Bit ..................................................................... 14 CCP1IE Bit ................................................................ 14 SSPIE Bit ................................................................... 14 TMR1IE Bit ................................................................ 14 TMR2IE Bit ................................................................ 14 Pinout Descriptions PIC16C62B/PIC16C72A ............................................. 6
DS35008B-page 114
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
PIR1 Register ............................................................... 9, 15 ADIF Bit ..................................................................... 15 CCP1IF Bit ................................................................. 15 SSPIF Bit ................................................................... 15 TMR1IF Bit ................................................................ 15 TMR2IF Bit ................................................................ 15 Pointer, FSR ...................................................................... 18 PORTA ................................................................................ 6 Analog Port Pins .......................................................... 6 PORTA Register ................................................... 9, 19 RA3:RA0 and RA5 Port Pins ..................................... 19 RA4/T0CKI Pin ..................................................... 6, 19 RA5/SS/AN4 Pin ................................................... 6, 39 TRISA Register ................................................... 10, 19 PORTB ................................................................................ 6 PORTB Register ................................................... 9, 21 Pull-up Enable (RBPU Bit) ......................................... 12 RB0/INT Edge Select (INTEDG Bit) .......................... 12 RB0/INT Pin, External .......................................... 6, 63 RB3:RB0 Port Pins .................................................... 21 RB7:RB4 Interrupt on Change ................................... 63 RB7:RB4 Interrupt on Change Enable (RBIE Bit) ............................................... 13, 63 RB7:RB4 Interrupt on Change Flag (RBIF Bit) ..............................................13, 21, 63 RB7:RB4 Port Pins .................................................... 21 TRISB Register ................................................... 10, 21 PORTC ................................................................................ 6 Block Diagram ........................................................... 23 PORTC Register ................................................... 9, 23 RC0/T1OSO/T1CKI Pin ............................................... 6 RC1/T1OSI Pin ............................................................ 6 RC2/CCP1 Pin ............................................................. 6 RC3/SCK/SCL Pin ................................................ 6, 39 RC4/SDI/SDA Pin ................................................. 6, 39 RC5/SDO Pin ....................................................... 6, 39 RC6 Pin ....................................................................... 6 RC7 Pin ....................................................................... 6 TRISC Register .................................................. 10, 23 Postscaler, Timer2 Select (TOUTPS3:TOUTPS0 Bits) ............................ 31 Postscaler, WDT ................................................................ 25 Assignment (PSA Bit) ......................................... 12, 25 Block Diagram ........................................................... 26 Rate Select (PS2:PS0 Bits) ................................ 12, 25 Switching Between Timer0 and WDT ........................ 26 Power-on Reset (POR) ........................... 55, 57, 59, 60, 61 Oscillator Start-up Timer (OST) .......................... 55, 59 POR Status (POR Bit) ............................................... 16 Power Control (PCON) Register ................................ 60 Power-down (PD Bit) .......................................... 11, 57 Power-on Reset Circuit, External .............................. 59 Power-up Timer (PWRT) .................................... 55, 59 PWRT Enable (PWRTE Bit) ...................................... 55 Time-out (TO Bit) ................................................ 11, 57 Time-out Sequence ................................................... 60 Timing Diagram ......................................................... 92 Prescaler, Capture ............................................................. 34 Prescaler, Timer0 .............................................................. 25 Assignment (PSA Bit) ......................................... 12, 25 Block Diagram ........................................................... 26 Rate Select (PS2:PS0 Bits) ................................ 12, 25 Switching Between Timer0 and WDT ........................ 26 Prescaler, Timer1 .............................................................. 28 Select (T1CKPS1:T1CKPS0 Bits)............................... 27 Prescaler, Timer2 .............................................................. 36 Select (T2CKPS1:T2CKPS0 Bits) ............................. 31 PRO MATE(R) II Universal Programmer ............................. 77 Program Counter PCL Register .........................................................9, 17 PCLATH Register ........................................... 9, 17, 63 Reset Conditions ....................................................... 60 Program Memory ................................................................. 7 Interrupt Vector ........................................................... 7 Paging ...................................................................7, 17 Program Memory Map ................................................ 7 Reset Vector ............................................................... 7 Program Verification .......................................................... 66 Programming Pin (Vpp) ....................................................... 6 Programming, Device Instructions .................................... 67 PWM (CCP Module) .......................................................... 36 Block Diagram ........................................................... 36 CCPR1H:CCPR1L Registers .................................... 36 Duty Cycle ................................................................. 36 Example Frequencies/Resolutions ............................ 37 Output Diagram ......................................................... 36 Period ........................................................................ 36 Set-Up for PWM Operation ....................................... 37 TMR2 to PR2 Match ............................................31, 36 TMR2 to PR2 Match Enable (TMR2IE Bit) ................ 14 TMR2 to PR2 Match Flag (TMR2IF Bit) .................... 15
Q
Q-Clock ............................................................................. 36
R
Register File ........................................................................ 8 Register File Map ................................................................ 8 Reset ...........................................................................55, 57 Block Diagram ........................................................... 58 Reset Conditions for All Registers ............................ 61 Reset Conditions for PCON Register ........................ 60 Reset Conditions for Program Counter ..................... 60 Reset Conditions for STATUS Register .................... 60 Timing Diagram ......................................................... 92 Revision History .............................................................. 111
S
SEEVAL(R) Evaluation and Programming System ............. 78 SLEEP .................................................................. 55, 57, 65 Software Simulator (MPLAB-SIM) ..................................... 76 Special Features of the CPU ............................................. 55 Special Function Registers .................................................. 9 Speed, Operating ................................................................ 1 SPI (SSP Module) Block Diagram ........................................................... 39 Buffer Full Status (BF Bit) ......................................... 46 Clock Edge Select (CKE Bit) ..................................... 46 Clock Polarity Select (CKP Bit) ................................. 47 Data Input Sample Phase (SMP Bit) ......................... 46 Mode Select (SSPM3:SSPM0 Bits) .......................... 47 Receive Overflow Indicator (SSPOV Bit) .................. 47 Serial Clock (RC3/SCK/SCL) .................................... 39 Serial Data In (RC4/SDI/SDA) .................................. 39 Serial Data Out (RC5/SDO) ...................................... 39 Slave Select (RA5/SS/AN4) ...................................... 39 Synchronous Serial Port Enable (SSPEN Bit) .......... 47
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 115
PIC16C62B/72A
SSP .................................................................................... 39 Enable (SSPIE Bit) .................................................... 14 Flag (SSPIF Bit) ......................................................... 15 RA5/SS/AN4 Pin .......................................................... 6 RC3/SCK/SCL Pin ....................................................... 6 RC4/SDI/SDA Pin ........................................................ 6 RC5/SDO Pin ............................................................... 6 SSPADD Register ...................................................... 10 SSPBUF Register ........................................................ 9 SSPCON Register ................................................ 9, 47 SSPSTAT Register ............................................. 10, 46 TMR2 Output for Clock Shift ...................................... 32 Write Collision Detect (WCOL Bit) ............................. 47 SSPCON Register ............................................................. 47 CKP Bit ...................................................................... 47 SSPEN Bit ................................................................. 47 SSPM3:SSPM0 Bits .................................................. 47 SSPOV Bit ................................................................. 47 WCOL Bit ................................................................... 47 SSPSTAT Register ............................................................ 46 BF Bit ......................................................................... 46 CKE Bit ...................................................................... 46 D/A Bit ........................................................................ 46 P bit ..................................................................... 45, 46 R/W Bit ................................................... 42, 43, 44, 46 S Bit .................................................................... 45, 46 SMP Bit ...................................................................... 46 UA Bit ......................................................................... 46 Stack .................................................................................. 17 STATUS Register ...................................................9, 11, 63 C Bit ........................................................................... 11 DC Bit ........................................................................ 11 IRP Bit ........................................................................ 11 PD Bit .................................................................. 11, 57 RP1:RP0 Bits ............................................................. 11 TO Bit .................................................................. 11, 57 Z Bit ........................................................................... 11 Timer1 ............................................................................... 27 Block Diagram ........................................................... 28 Capacitor Selection ................................................... 29 Clock Source Select (TMR1CS Bit) ........................... 27 External Clock Input Sync (T1SYNC Bit) .................. 27 Module On/Off (TMR1ON Bit) ................................... 27 Oscillator .............................................................27, 29 Oscillator Enable (T1OSCEN Bit) .............................. 27 Overflow Enable (TMR1IE Bit) .................................. 14 Overflow Flag (TMR1IF Bit) ....................................... 15 Overflow Interrupt ................................................27, 29 RC0/T1OSO/T1CKI Pin ............................................... 6 RC1/T1OSI .................................................................. 6 Special Event Trigger (CCP) ...............................29, 35 T1CON Register ....................................................9, 27 Timing Diagram ......................................................... 93 TMR1H Register .......................................................... 9 TMR1L Register .......................................................... 9 Timer2 Block Diagram ........................................................... 32 PR2 Register ................................................ 10, 31, 36 SSP Clock Shift ......................................................... 32 T2CON Register ....................................................9, 31 TMR2 Register ......................................................9, 31 TMR2 to PR2 Match Enable (TMR2IE Bit) ................ 14 TMR2 to PR2 Match Flag (TMR2IF Bit) .................... 15 TMR2 to PR2 Match Interrupt ...................... 31, 32, 36 Timing Diagrams I2C Reception (7-bit Address) ................................... 43 Wake-up from SLEEP via Interrupt ........................... 66 Timing Diagrams and Specifications ................................. 90 A/D Conversion ....................................................... 102 Brown-out Reset (BOR) ............................................ 92 Capture/Compare/PWM (CCP) ................................. 94 CLKOUT and I/O ....................................................... 91 External Clock ........................................................... 90 I2C Bus Data ........................................................... 100 I2C Bus Start/Stop Bits .............................................. 99 Oscillator Start-up Timer (OST) ................................. 92 Power-up Timer (PWRT) ........................................... 92 Reset ........................................................................... 2 Timer0 and Timer1 .................................................... 93 Watchdog Timer (WDT) ............................................ 92
T
T1CON Register ........................................................... 9, 27 T1CKPS1:T1CKPS0 Bits ........................................... 27 T1OSCEN Bit ............................................................. 27 T1SYNC Bit ............................................................... 27 TMR1CS Bit ............................................................... 27 TMR1ON Bit .............................................................. 27 T2CON Register ........................................................... 9, 31 T2CKPS1:T2CKPS0 Bits ........................................... 31 TMR2ON Bit .............................................................. 31 TOUTPS3:TOUTPS0 Bits .......................................... 31 Timer0 ................................................................................ 25 Block Diagram ........................................................... 25 Clock Source Edge Select (T0SE Bit) ................ 12, 25 Clock Source Select (T0CS Bit) .......................... 12, 25 Overflow Enable (T0IE Bit) ........................................ 13 Overflow Flag (T0IF Bit) ...................................... 13, 63 Overflow Interrupt ............................................... 26, 63 RA4/T0CKI Pin, External Clock ................................... 6 Timing Diagram ......................................................... 93 TMR0 Register ............................................................. 9
W
W Register ......................................................................... 63 Wake-up from SLEEP .................................................55, 65 Interrupts .............................................................60, 61 MCLR Reset .............................................................. 61 Timing Diagram ......................................................... 66 WDT Reset ................................................................ 61 Watchdog Timer (WDT) ..............................................55, 64 Block Diagram ........................................................... 64 Enable (WDTE Bit) ..............................................55, 64 Programming Considerations .................................... 64 RC Oscillator ............................................................. 64 Timing Diagram ......................................................... 92 WDT Reset, Normal Operation .................... 57, 60, 61 WDT Reset, SLEEP ..................................... 57, 60, 61 WWW, On-Line Support ...................................................... 3
DS35008B-page 116
Preliminary
(c) 1999 Microchip Technology Inc.
PIC16C62B/72A
ON-LINE SUPPORT
Microchip provides on-line support on the Microchip World Wide Web (WWW) site. The web site is used by Microchip as a means to make files and information easily available to customers. To view the site, the user must have access to the Internet and a web browser, such as Netscape or Microsoft Explorer. Files are also available for FTP download from our FTP site.
Systems Information and Upgrade Hot Line
The Systems Information and Upgrade Line provides system users a listing of the latest versions of all of Microchip's development systems software products. Plus, this line provides information on how customers can receive any currently available upgrade kits.The Hot Line Numbers are: 1-800-755-2345 for U.S. and most of Canada, and 1-480-786-7302 for the rest of the world.
981103
Connecting to the Microchip Internet Web Site
The Microchip web site is available by using your favorite Internet browser to attach to: www.microchip.com The file transfer site is available by using an FTP service to connect to: ftp://ftp.microchip.com The web site and file transfer site provide a variety of services. Users may download files for the latest Development Tools, Data Sheets, Application Notes, User's Guides, Articles and Sample Programs. A variety of Microchip specific business information is also available, including listings of Microchip sales offices, distributors and factory representatives. Other data available for consideration is: * Latest Microchip Press Releases * Technical Support Section with Frequently Asked Questions * Design Tips * Device Errata * Job Postings * Microchip Consultant Program Member Listing * Links to other useful web sites related to Microchip Products * Conferences for products, Development Systems, technical information and more * Listing of seminars and events
Trademarks: The Microchip name, logo, PIC, PICmicro, PICSTART, PICMASTER and PRO MATE are registered trademarks of Microchip Technology Incorporated in the U.S.A. and other countries. FlexROM, MPLAB and fuzzyLAB are trademarks and SQTP is a service mark of Microchip in the U.S.A. All other trademarks mentioned herein are the property of their respective companies.
(c) 1999 Microchip Technology Inc.
Preliminary
DS35008B-page 117
PIC16C62B/72A
READER RESPONSE
It is our intention to provide you with the best documentation possible to ensure successful use of your Microchip product. If you wish to provide your comments on organization, clarity, subject matter, and ways in which our documentation can better serve you, please FAX your comments to the Technical Publications Manager at (480) 786-7578. Please list the following information, and use this outline to provide us with your comments about this Data Sheet. To: RE: Technical Publications Manager Reader Response Total Pages Sent
From: Name Company Address City / State / ZIP / Country Telephone: (_______) _________ - _________ Application (optional): Would you like a reply? Device: PIC16C62B/72A Questions: 1. What are the best features of this document? Y N Literature Number: DS35008B FAX: (______) _________ - _________
2. How does this document meet your hardware and software development needs?
3. Do you find the organization of this data sheet easy to follow? If not, why?
4. What additions to the data sheet do you think would enhance the structure and subject?
5. What deletions from the data sheet could be made without affecting the overall usefulness?
6. Is there any incorrect or misleading information (what and where)?
7. How would you improve this document?
8. How would you improve our software, systems, and silicon products?
DS35008B-page 118
Preliminary
(c) 1998 Microchip Technology Inc.
PIC16C62B/72A
PIC16C62B/72A PRODUCT IDENTIFICATION SYSTEM
To order or obtain information, e.g., on pricing or delivery refer to the factory or the listed sales office. PART NO. -XX X /XX XXX Pattern: Package: QTP, SQTP, Code or Special Requirements JW SO SP P SS I E 04 10 20 = = = = = Windowed CERDIP SOIC Skinny plastic dip PDIP SSOP Examples
a) PIC16C72A-04/P 301 Commercial Temp., PDIP Package, 4 MHz, normal VDD limits, QTP pattern #301
Temperature Range: Frequency Range: Device
= 0C to +70C = -40C to +85C = -40C to +125C = 4 MHz = 10 MHz = 20 MHz
VDD range 4.0V to 5.5V VDD range 4.0V to 5.5V (Tape/Reel) VDD range 2.5V to 5.5V VDD range 2.5V to 5.5V (Tape/Reel)
b)
PIC16C62B: PIC16C62BT: PIC16LC62B: PIC16LC62BT:
* JW Devices are UV erasable and can be programmed to any device configuration. JW Devices meet the electrical requirement of each oscillator type (including LC devices).
Sales and Support
Data Sheets Products supported by a preliminary Data Sheet may have an errata sheet describing minor operational differences and recommended workarounds. To determine if an errata sheet exists for a particular device, please contact one of the following: 1. 2. 3. Your local Microchip sales office The Microchip Corporate Literature Center U.S. FAX: (480) 786-7277 The Microchip Worldwide Site (www.microchip.com)
Please specify which device, revision of silicon and Data Sheet (include Literature #) you are using. New Customer Notification System Register on our web site (www.microchip.com/cn) to receive the most current information on our products.
(c) 1998 Microchip Technology Inc.
Preliminary
DS35008B-page 119
WORLDWIDE SALES AND SERVICE
AMERICAS
Corporate Office
Microchip Technology Inc. 2355 West Chandler Blvd. Chandler, AZ 85224-6199 Tel: 480-786-7200 Fax: 480-786-7277 Technical Support: 480-786-7627 Web Address: http://www.microchip.com
AMERICAS (continued)
Toronto
Microchip Technology Inc. 5925 Airport Road, Suite 200 Mississauga, Ontario L4V 1W1, Canada Tel: 905-405-6279 Fax: 905-405-6253
ASIA/PACIFIC (continued)
Singapore
Microchip Technology Singapore Pte Ltd. 200 Middle Road #07-02 Prime Centre Singapore 188980 Tel: 65-334-8870 Fax: 65-334-8850
ASIA/PACIFIC
Hong Kong
Microchip Asia Pacific Unit 2101, Tower 2 Metroplaza 223 Hing Fong Road Kwai Fong, N.T., Hong Kong Tel: 852-2-401-1200 Fax: 852-2-401-3431
Taiwan, R.O.C
Microchip Technology Taiwan 10F-1C 207 Tung Hua North Road Taipei, Taiwan, ROC Tel: 886-2-2717-7175 Fax: 886-2-2545-0139
Atlanta
Microchip Technology Inc. 500 Sugar Mill Road, Suite 200B Atlanta, GA 30350 Tel: 770-640-0034 Fax: 770-640-0307
Boston
Microchip Technology Inc. 5 Mount Royal Avenue Marlborough, MA 01752 Tel: 508-480-9990 Fax: 508-480-8575
EUROPE
United Kingdom
Arizona Microchip Technology Ltd. 505 Eskdale Road Winnersh Triangle Wokingham Berkshire, England RG41 5TU Tel: 44 118 921 5858 Fax: 44-118 921-5835
Beijing
Microchip Technology, Beijing Unit 915, 6 Chaoyangmen Bei Dajie Dong Erhuan Road, Dongcheng District New China Hong Kong Manhattan Building Beijing 100027 PRC Tel: 86-10-85282100 Fax: 86-10-85282104
Chicago
Microchip Technology Inc. 333 Pierce Road, Suite 180 Itasca, IL 60143 Tel: 630-285-0071 Fax: 630-285-0075
India
Microchip Technology Inc. India Liaison Office No. 6, Legacy, Convent Road Bangalore 560 025, India Tel: 91-80-229-0061 Fax: 91-80-229-0062
Denmark
Microchip Technology Denmark ApS Regus Business Centre Lautrup hoj 1-3 Ballerup DK-2750 Denmark Tel: 45 4420 9895 Fax: 45 4420 9910
Dallas
Microchip Technology Inc. 4570 Westgrove Drive, Suite 160 Addison, TX 75248 Tel: 972-818-7423 Fax: 972-818-2924
Japan
Microchip Technology Intl. Inc. Benex S-1 6F 3-18-20, Shinyokohama Kohoku-Ku, Yokohama-shi Kanagawa 222-0033 Japan Tel: 81-45-471- 6166 Fax: 81-45-471-6122
France
Arizona Microchip Technology SARL Parc d'Activite du Moulin de Massy 43 Rue du Saule Trapu Batiment A - ler Etage 91300 Massy, France Tel: 33-1-69-53-63-20 Fax: 33-1-69-30-90-79
Dayton
Microchip Technology Inc. Two Prestige Place, Suite 150 Miamisburg, OH 45342 Tel: 937-291-1654 Fax: 937-291-9175
Detroit
Microchip Technology Inc. Tri-Atria Office Building 32255 Northwestern Highway, Suite 190 Farmington Hills, MI 48334 Tel: 248-538-2250 Fax: 248-538-2260
Korea
Microchip Technology Korea 168-1, Youngbo Bldg. 3 Floor Samsung-Dong, Kangnam-Ku Seoul, Korea Tel: 82-2-554-7200 Fax: 82-2-558-5934
Germany
Arizona Microchip Technology GmbH Gustav-Heinemann-Ring 125 D-81739 Munchen, Germany Tel: 49-89-627-144 0 Fax: 49-89-627-144-44
Los Angeles
Microchip Technology Inc. 18201 Von Karman, Suite 1090 Irvine, CA 92612 Tel: 949-263-1888 Fax: 949-263-1338
Italy
Arizona Microchip Technology SRL Centro Direzionale Colleoni Palazzo Taurus 1 V. Le Colleoni 1 20041 Agrate Brianza Milan, Italy Tel: 39-039-65791-1 Fax: 39-039-6899883
11/15/99
Shanghai
Microchip Technology RM 406 Shanghai Golden Bridge Bldg. 2077 Yan'an Road West, Hong Qiao District Shanghai, PRC 200335 Tel: 86-21-6275-5700 Fax: 86 21-6275-5060
New York
Microchip Technology Inc. 150 Motor Parkway, Suite 202 Hauppauge, NY 11788 Tel: 631-273-5305 Fax: 631-273-5335
San Jose
Microchip Technology Inc. 2107 North First Street, Suite 590 San Jose, CA 95131 Tel: 408-436-7950 Fax: 408-436-7955
Microchip received QS-9000 quality system certification for its worldwide headquarters, design and wafer fabrication facilities in Chandler and Tempe, Arizona in July 1999. The Company's quality system processes and procedures are QS-9000 compliant for its PICmicro(R) 8-bit MCUs, KEELOQ(R) code hopping devices, Serial EEPROMs and microperipheral products. In addition, Microchip's quality system for the design and manufacture of development systems is ISO 9001 certified.
All rights reserved. (c) 1999 Microchip Technology Incorporated. Printed in the USA. 11/99
Printed on recycled paper.
Information contained in this publication regarding device applications and the like is intended for suggestion only and may be superseded by updates. No representation or warranty is given and no liability is assumed by Microchip Technology Incorporated with respect to the accuracy or use of such information, or infringement of patents or other intellectual property rights arising from such use or otherwise. Use of Microchip's products as critical components in life support systems is not authorized except with express written approval by Microchip. No licenses are conveyed, implicitly or otherwise, under any intellectual property rights. The Microchip logo and name are registered trademarks of Microchip Technology Inc. in the U.S.A. and other countries. All rights reserved. All other trademarks mentioned herein are the property of their respective companies.
1999 Microchip Technology Inc.

▲Up To Search▲

Price & Availability of PIC16C72A-04IP

	To Download PIC16C72A-04IP Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .